Mada za sehemu hiiConstructing simple heating coilsMada 2
- Building circuit with heating coils in series
- Building a circuit with heating coils in parallel
Building a Circuit with Heating Coils in Parallel
A parallel heating circuit connects multiple heating coils so that each coil has its own independent path to the power source. Unlike series circuits where coils share one path, in parallel circuits each coil connects directly to the voltage source. This means each heating element receives the full supply voltage and operates independently of the others.
When one heating coil in a parallel circuit fails or burns out, the other coils continue to work without interruption. This is a major advantage of parallel connections, which is why many household heating appliances use this arrangement.
Voltage and Current in Parallel
In a parallel heating circuit:
- Voltage is the same across each heating coil because each branch connects directly to the power source terminals.
- Current divides among the parallel branches. Each coil draws current according to its resistance using Ohm's Law: I=RV
- The total current from the power supply equals the sum of currents through all individual coils.
Resistance in Parallel
The total resistance of parallel heating coils is always less than the smallest individual resistance. For two coils with resistances R1 and R2 connected in parallel:
Rtotal1=R11+R21
Or for two equal resistances R:
Rtotal=2R
- Independent operation — Each coil works independently; if one fails, others continue functioning.
- Full voltage supply — Each coil receives the full mains voltage, ensuring proper heating performance.
- Reliability — The failure of one heating element does not shut down the entire system.
- Easy troubleshooting — Problems can be identified by testing each branch separately.
- Higher total current — The power supply must provide current for all branches simultaneously.
- Complex wiring — More connections are required compared to series circuits.
- Increased energy consumption — All coils operate at full power when switched on.
Question: Two heating coils, each with a resistance of 20 Ω, are connected in parallel to a 240 V AC supply.
Calculate: a) The voltage across each coil b) The current through each coil c) The total current drawn from the supply d) The total resistance of the circuit
Solution:
a) Voltage across each coil = 240 V (same as supply in parallel)
b) Current through each coil using Ohm's Law: I=RV=20Ω240V=12A
c) Total current = sum of currents through each branch: Itotal=12A+12A=24A
d) Total resistance: Rtotal=nR=220Ω=10Ω
Or using the formula: Rtotal1=201+201=202=101 Rtotal=10Ω
Tools and Materials Required
- Soldering iron
- Electrician's knife
- Stopwatch
- Digital multimeters
- Workbench
- Heating coils (two or more)
- Connecting wires
- Switching devices
- Wiring diagram
- Personal Protective Equipment (PPE)
Safety Measures
- Wear appropriate PPE including overalls and safety goggles
- Ensure all components are rated for the correct voltage and current
- Use insulated, heat-resistant wires
- Never touch coils when power is ON
- Ensure all connections are tight and well-insulated
- Always ask your teacher before powering the circuit
Construction Steps
- Prepare your work area — Wear PPE and clear your workbench.
- Study the wiring diagram — Identify all components and their positions.
- Select tools and materials — Gather everything needed for the circuit.
- Connect the coils in parallel — Connect one end of each coil to the live supply and the other end to the neutral return, ensuring each has its own branch. Do not switch ON power yet.
- Request inspection — Ask your teacher to check your wiring and confirm safety.
- Power the circuit — Switch ON only after teacher approval.
- Take measurements — Record voltage across and current through each coil.
- Collect data — Run for a set time (e.g., 30 seconds) and observe heat output.
- Switch OFF and cool — Turn off power and allow coils to cool before touching.
- Calculate results — Compute heat produced, resistance, and power for each coil.
- Record observations — Write all results in a table format.
Calculations After Measurement
To calculate heat produced by each coil:
H=I2×R×t
Where:
- H = heat produced (Joules)
- I = current through coil (Amperes)
- R = resistance of coil (Ohms)
- t = time current flows (seconds)
Power dissipated by each coil:
P=I×V=I2×R=RV2
Heating appliances like electric kettles, stoves, and water heaters use parallel connections because:
- Each heating element receives full voltage and produces maximum heat.
- Multiple heating levels can be achieved by switching different coils on or off.
- If one heating element fails, the appliance can still function with remaining elements.
- Each element operates independently at its designed power rating.
- Parallel heating circuits provide independent paths for each heating coil to the power source.
- Each coil receives the same voltage as the supply.
- Current divides among branches based on individual coil resistances.
- Total resistance decreases as more coils are added in parallel.
- Parallel connections offer reliability and independent operation, making them ideal for household heating appliances.
In Tanzania, electric water heaters and cooking stoves found in homes and restaurants (such as in Arusha or Dar es Salaam) use heating coils connected in parallel. For example, a 3-kettle electric cooking stove may have three heating elements, each rated at 1000W connected in parallel to the 240V supply. If one element burns out, the other two continue working, allowing the chef to keep cooking. This parallel arrangement ensures reliability in busy commercial kitchens and households where continuous operation is important for preparing meals like ugali or boiling water for tea.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear.
- Design a circuit diagram of the heating circuit.
- Prepare heating coils for connection.
- Build parallel coils circuit.
- Supply power to the circuits.
- Perform power measurement.
- Test the circuits.
- Observe safety precautions.
Tathmini ya matokeo
Heating circuits are constructed in parallel per IEE regulations and the test results conform to approved standards and theories.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to build a circuit with heating coils in parallel.
Principles: The student should explain the principles related to building a circuit with heating coils in parallel
Theories: The student should explain:
- The difference between resistance and inductive reactance.
- The uses of various tools and equipment.
- I.E.E. Regulations.
- Measurement of current in the circuit.
- Measurement of voltage in the circuits.
Detailed knowledge about:
- Safe handling of working tools and equipment
- Electrical hazards
- First aid
- Safety rules
- Precautions to be taken during working
Swali
In a parallel heating circuit, what quantity is the same across each heating coil?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado