Mada za sehemu hiiErecting conduitsMada 2
- Erecting PVC conduits
- Erecting galvanized conduit
PVC conduits are tubes made from polyvinyl chloride (PVC), a type of plastic used to protect and route electrical wires and cables in buildings. They shield cables from physical damage, moisture, dust, chemicals, and harsh weather, which extends the lifespan of the wiring system. PVC conduits make electrical installation easier, allow the use of single-core cables to reduce costs, and improve electrical safety by lowering the risk of shocks and short circuits.
Rigid PVC Conduits
Rigid PVC conduits are the most common type used in electrical installations. They have higher mechanical strength compared to flexible conduits and maintain their shape once installed. These conduits are ideal for straight runs and areas where the wiring path does not require frequent bending.
Flexible PVC Conduits
Flexible PVC conduits can be bent to navigate curves and tight spaces where rigid conduits would be difficult to install. They are commonly used in areas with irregular surfaces or where movement may occur, such as in connection to machinery or equipment.
- Lightweight: Easy to handle and install, reducing labor time and effort.
- Corrosion resistant: Suitable for use in damp and humid environments without rusting.
- Cost-effective: Cheaper than metal conduits, making them a common choice for residential and commercial installations.
- Leak-proof joints: Provide tight connections that protect cables from moisture ingress.
- Lower mechanical strength: Can be damaged by heavy impact or pressure.
- Not suitable for high temperatures: Can deform or melt when exposed to excessive heat.
PVC conduits are widely used in residential electrical installations for wiring inside walls, ceilings, and floors. They are also suitable for underground wiring because they do not corrode or decompose. In commercial and industrial buildings, their durability and moisture resistance make them an ideal choice for many applications.
When installing conduits, electricians often encounter obstacles or corners that require the conduit to change direction. Bending is the process of shaping conduits to navigate these obstacles while maintaining a continuous path for the cables.
Types of Conduit Bends
90° Stub-up Bend
This is the most common bend, formed by bending the conduit into an L shape or a 90° angle. It is used to run conduits up or down walls, through floors or ceilings, and to make corner turns.
90° Back-to-back Bend
This bend consists of two consecutive 90° bends and is used when a conduit needs to change direction twice in a tight space, such as running around a beam.
Offset Bend
An offset bend creates an S-shape, allowing the conduit to navigate around obstacles while changing elevation. This is commonly used when passing over existing pipes or structural elements.
Saddle Bend
A saddle bend enables the conduit to pass over an obstacle and return to its original path. It is useful for crossing over existing conduits, beams, or plumbing pipes.
Cold Bending vs. Hot Bending
Cold bending is performed at room temperature without heat. It is more applicable to metal conduits and produces smooth curves quickly. It is not suitable for PVC conduits because PVC is brittle when cold.
Hot bending is commonly used for PVC conduits. The conduit is heated until it becomes flexible, then bent to the desired shape. Care must be taken to avoid burning the material. The steps for hot bending are:
- Measure and mark the exact point where the bend is required.
- Heat the marked section evenly using a heat gun until it becomes soft and flexible.
- Support the heated section on a bending former or carefully with hands to prevent kinking.
- Gently bend the conduit to the desired angle, keeping smooth pressure along the heated section.
- Hold the conduit in position until it cools and hardens.
The space factor refers to the ratio of space occupied by cables to the total internal space inside the conduit. According to standards, the space factor for conduits is limited to 40%. This means no more than 40% of the conduit's internal cross-sectional area should be filled with cables.
Why Space Factor Matters
- Prevents insulation damage during cable pulling
- Reduces mechanical stress on cables
- Prevents heat buildup inside the conduit
- Allows for future additions or changes to the wiring
Worked Example
A conduit has an internal cross-sectional area of 300 mm². Calculate the maximum total cross-sectional area of cables that can be installed inside it.
Solution:
Maximum cable area = Space factor × Conduit internal area = 0.40 × 300 mm² = 120 mm²
Therefore, the cables installed must not have a total cross-sectional area exceeding 120 mm².
Required Tools
- Combination pliers
- Electrician knife
- Measuring tape
- Long nose pliers
- Claw hammer
- Set of screwdrivers
- Bench vice
- Bending block or bending machine
- Draw wire (snake wire)
- Round files
- Spirit level
- Chisel
- Chest drill machine
- Heat gun (for hot bending)
Safety Gear (PPE)
- Leather gloves
- Overalls
- Safety boots
- Safety goggles
Before starting work, wear appropriate PPE and check the site for hazards such as flammable materials or unstable surfaces. Ensure the power supply is switched off and locked out before beginning work. Confirm that the conduits are of the correct size and type for the installation.
During installation, route conduits safely away from other services like communication cables, water pipes, and fuel lines. Ensure conduits are well secured and supported at appropriate intervals. Follow manufacturer guidelines and standards for bending conduits to avoid damaging them.
After installation, perform visual inspection to ensure everything is correctly in place and free from obstructions.
In Tanzania, electricians use PVC conduits extensively when wiring new houses in areas like Mikocheni or when rewiring old buildings in Dar es Salaam. For example, when installing a new socket circuit in a home in Arusha, a qualified electrician would use 20 mm PVC conduits to protect the 2.5 mm² cables running from the distribution board to the socket outlets, ensuring the wiring is safe, lasts for many years, and meets the required Tanzanian electrical standards.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret architectural drawing.
- Draw electrical diagrams.
- Identify tools, equipment and materials required.
- Mark the conduit run.
- Cut/chase in the wall for conduits.
- Cut conduit for the required length.
- Make bends and corners.
- Mount the conduits and support them.
- Clean work area.
- Store tools, equipment and safety gears.
Tathmini ya matokeo
The PVC conduit system is securely mounted as per procedures prescribed by the I.E.E. regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to Erect PVC conduits systems.
Principles: The student should explain the principles related to erecting PVC conduits.
Theories: The student should explain:
- The types and size of conduit.
- The types of bends.
- The application of plastic conduits.
- Space factor of the conduit.
- Advantage and disadvantages of conduit wiring system.
Detailed knowledge about:
- Safety precautions on choosing conduit size.
- I.E.E. regulations
- Maintenance of buildings
Swali
What is the primary purpose of PVC conduits in electrical installations?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado