Mada za sehemu hiiPerforming gas welding and brazingMada 4
- Assembling oxy-acetylene plant
- Performing fusion welding
- Performing hard soldering
- Gas cutting
Fusion welding is a process in which two metal pieces are joined together by melting the edges of the metals and allowing them to cool and fuse into a single piece. This is different from non-fusion welding, where the metals are joined without melting the base metal itself — instead, a filler material is used to create the joint. In plumbing and pipe fitting, fusion welding is commonly used to join copper pipes and fittings, as well as certain plastic pipes, creating strong and leak-proof connections.
Fusion welding can produce several types of joints depending on the position and configuration of the materials being joined:
- Butt joint — Two pipes or sheets are placed end to end and welded along the seam
- Lap joint — One piece overlaps the other, and the overlapping area is welded
- T-joint — One piece meets another at a 90-degree angle, forming a "T" shape
- Corner joint — Two pieces meet at a right angle to form a corner
Before performing fusion welding, gather the following materials and tools:
- Oxy-acetylene plant — The main source of heat, consisting of oxygen and acetylene gas cylinders
- Pressure regulator — Controls the gas pressure from the cylinders to safe working levels
- Welding torch (blowpipe) — Mixes oxygen and acetylene to produce the flame
- Hose pipes — Transport gases from the regulators to the torch
- Spark lighter — Safely ignites the gases
- Ball peen hammer — Used for shaping and finishing metal after welding
- Chisel and centre punch — For marking and cutting metal
- Tongs — Hold hot metal pieces safely
- Safety equipment — Goggles, safety boots, gloves, and leather apron
- Measuring tools — Steel ruler or folding ruler, hacksaw for cutting
Always observe the following safety rules when performing fusion welding:
- Wear approved safety goggles, gloves, leather apron, and safety boots at all times
- Check all connections for leaks before lighting the torch
- Keep fire-fighting equipment (extinguisher, sand bucket) nearby
- Ensure good ventilation in the workshop to disperse harmful gases
- Never leave a lit torch unattended
- Keep flammable materials away from the work area
- Allow welded pieces to cool before handling them with tongs
Follow these steps to carry out fusion welding correctly:
-
Prepare the materials — Cut the pipes or metal pieces to the required size using a hacksaw. Clean the surfaces to be joined using a wire brush or emery cloth to remove dirt, rust, or grease.
-
Fit the joint — Position the pieces in the desired joint configuration (butt, lap, T, or corner). Use a clamp or jig to hold them firmly in place.
-
Set up the equipment — Connect the hose pipes to the oxygen and acetylene cylinders. Attach the pressure regulators and set the correct working pressure (typically 3–5 psi for acetylene and 10–15 psi for oxygen).
-
Light the torch — Open the acetylene valve slightly and light with a spark lighter. Then gradually open the oxygen valve until a neutral flame (bright white inner cone) is obtained.
-
Heat the joint — Direct the inner cone of the flame onto the joint area. Move the torch in a circular or weaving motion to heat both pieces evenly until they reach a molten state.
-
Add filler material (if needed) — If welding copper or steel, introduce a suitable filler rod into the molten pool and let it flow into the joint.
-
Cool the joint — Allow the welded joint to cool naturally. Do not quench with water as this may cause cracking.
-
Inspect and finish — Check the weld for uniformity and strength. Use a ball peen hammer to remove any slag or rough edges.
A plumber needs to join two lengths of 15 mm copper pipe to extend a water line in a house. The pipes are cut to length, and the ends are cleaned with emery cloth. The pipes are placed end to end in a butt joint configuration and held with a pipe clamp. The torch is lit and adjusted to a neutral flame. The plumber heats both pipe ends evenly, rotating the torch around the joint. When the copper turns a bright cherry-red and begins to melt, a copper filler rod is added to the joint. The flame is then withdrawn, and the weld cools slowly to form a strong, leak-proof connection.
In Tanzania, fusion welding skills are essential for plumbers working on water supply and drainage systems in homes, schools, and hospitals. For example, a plumber in Arusha using oxy-acetylene welding to join copper pipes for a new bathroom installation in a customer's house can create permanent, leak-proof joints that prevent water wastage and costly repairs. These skills also enable local tradespeople to offer repair services for geysers, solar water heating systems, and irrigation pipelines in their communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Inspect oxy-acetylene gas welding equipment
- Check root penetration
- Perform fusion joint
- Clean work place
- Clean tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
Fusion welding performed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used:
- The student should explain different techniques of performing fusion welding
Principles: The student should explain the principles of: -
- Performing fusion welding
Theories: The student should explain: -
- Materials used fusion welding
- Importance of fusion welding
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing fusion welding
- First aid
Swali
What is fusion welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado