Mada za sehemu hiiPerforming gas welding and brazingMada 4
Gas cutting is a thermal cutting process that uses a combination of oxygen and a fuel gas (usually acetylene) to melt and sever metal. It is widely used in plumbing and metal fabrication work for cutting steel plates, pipes, and sections quickly and accurately.
Gas cutting is used in the following common applications:
- Cutting steel plates and sheets to required sizes
- Cutting pipes to exact lengths during plumbing installations
- Removing damaged or worn metal parts during repairs
- Preparing metal edges for welding and brazing
- Creating openings in metal structures
- Cutting angles and curves in sheet metal work
- Speed – Cuts through thick metal faster than some mechanical methods
- Portability – Equipment can be moved to the work site easily
- Cost-effective – Lower initial cost compared to plasma cutting machines
- Versatility – Can cut various thicknesses of steel
- Clean cuts – Produces smooth edges with minimal additional finishing
- Simple operation – Easier to learn compared to other cutting methods
- Heat-affected zone – The heat can change the properties of the metal near the cut
- Fire hazard – Open flame poses a fire risk if not properly controlled
- Limited to ferrous metals – Cannot cut stainless steel or aluminum effectively
- Requires good ventilation – Produces fumes and sparks that need proper extraction
- Skilled operator needed – Improper technique produces poor-quality cuts
Always observe these safety measures when performing gas cutting:
- Wear appropriate PPE: safety goggles, gloves, leather apron, and safety boots
- Ensure the work area is clear of flammable materials
- Check all connections for leaks before igniting the torch
- Keep a fire extinguisher nearby at all times
- Work in a well-ventilated area to avoid fume inhalation
- Never leave the lit torch unattended
- Keep the torch pointed away from yourself and others when lighting
- Allow cut metal to cool before handling with tongs
The following equipment is needed for gas cutting:
- Oxy-acetylene plant (oxygen and acetylene cylinders)
- Pressure regulator (for both gases)
- Welding torch (cutting torch)
- Hose pipes (red for acetylene, green or blue for oxygen)
- Trolley for cylinder transport
- Blow pipe spanner
- Spark lighter
- Ball peen hammer
- Chase and centre punch (for marking)
- Tongs for handling hot metal
- Goggles, safety boots, gloves, and leather apron
Step 1: Preparation
- Set up the oxy-acetylene plant on a secure trolley
- Connect the correct hose pipes to the regulators (red for acetylene, green/blue for oxygen)
- Check all connections for leaks using soap solution
- Mark the cutting line on the metal using a centre punch and scribe
Step 2: Setting the Pressures
- Open the cylinder valves slowly
- Adjust the oxygen pressure to approximately 2–4 bar (depending on metal thickness)
- Adjust the acetylene pressure to approximately 0.5–1 bar
- The flame should be neutral (with equal oxygen and acetylene)
Step 3: Lighting the Torch
- Open the acetylene valve slightly and ignite with a spark lighter
- Adjust until the flame is steady
- Open the oxygen valve gradually to obtain a neutral welding flame
- For cutting, increase the oxygen stream to create the cutting jet
Step 4: Cutting the Metal
- Hold the torch at the starting point with the flame preheating the metal
- Once the metal reaches ignition temperature (bright red), slowly open the oxygen lever
- Move the torch steadily along the marked line at a consistent speed
- The oxygen stream will blow away the molten metal, creating the cut
Step 5: Finishing
- Close the oxygen valve first, then the acetylene valve
- Allow the metal to cool before handling
- Inspect the cut for smoothness and accuracy
A plumber needs to cut a mild steel plate 10 mm thick to make a rectangular cover for a water tank. The plate measures 600 mm × 400 mm. Using gas cutting:
- Mark the dimensions – Mark 600 mm × 400 mm on the plate using a steel rule and centre punch
- Set pressures – Oxygen at 3 bar, acetylene at 0.7 bar for 10 mm thick steel
- Light and adjust – Create a neutral preheating flame
- Cut along lines – Preheat each corner, then cut along each marked line moving steadily
- Check result – The cut edges should be smooth with minimal slag
The plumber has now created the correctly sized cover using gas cutting equipment available in the workshop.
In Tanzania, gas cutting is commonly used by local metalworkers and plumbers in markets such as Mwanza and Arusha to cut steel pipes and sheets for building construction, water tank fabrication, and repair of agricultural equipment. A small business owner in Dar es Salaam might use gas cutting to create custom metal doors, window frames, or plumbing fittings, earning income by providing these services to local customers who need custom metalwork for their homes or businesses.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Prepare the work piece to be cut
- Perform gas cutting
- Clean work place
- Clean tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
Cutting by gas performed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used:
- The student should explain different techniques of gas cutting.
Principles: The student should explain the principles of: -
- Gas cutting
Theories: The student should explain: -
- Procedures of gas cutting.
- Advantages of using gas to cut a metal
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while cutting metal with gas
- First aid
Swali
Gas cutting is a thermal cutting process that uses a combination of oxygen and which fuel gas to sever metal?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado