Mada za sehemu hiiPerforming arc weldingMada 6
- Starting and welding straight bead
- Performing butt joints
- Performing groove butt joints
- Performing lap joints
- Performing corner joints
- Performing T-joint
Starting and Welding Straight Bead
Welding is a process of joining two pieces of metal together by heating them to a melting point and allowing them to cool and fuse. In plumbing and pipe fitting, a straight bead is a continuous line of weld metal deposited along a joint. Learning to produce a uniform straight bead is a fundamental skill that forms the basis for all arc welding work in sheet metal fabrication.
- Arc welding: A welding process that uses an electric arc to heat and melt the base metal and filler rod.
- Straight bead: A weld deposit made in a single pass, producing a smooth, uniform line of fused metal along a joint.
- Filler rod: A metal rod that is melted to fill the joint between two workpieces.
- Weld pool: The molten metal at the point of welding before it solidifies.
- Strike: The act of starting the arc to begin welding.
Before starting any welding work, ensure the following tools and materials are available:
- Welding machine (DC or AC arc welder)
- Welding electrodes (E6013 or similar for mild steel)
- Work bench and bench vice
- Chipping hammer (for removing slag)
- Wire brush (for cleaning weld seams)
- Welding tongs (for holding hot workpieces)
- Safety shield or helmet with welding lens
- Leather gloves and leather apron
- Overalls and safety boots
- Try square, steel rule, and tape measure
- Hacksaw (for cutting metal)
- Scriber and centre punch (for marking)
- Ball peen hammer (for shaping metal)
Arc welding involves dangerous heat, bright light, and harmful fumes. Always observe these safety rules:
- Wear full protective clothing: leather gloves, apron, overalls, and safety boots at all times.
- Use a welding shield or helmet with the correct shade lens to protect your eyes from the intense arc light.
- Ensure the welding area is free from flammable materials.
- Keep the welding cable in good condition and away from heat sources.
- Work in a well-ventilated area to avoid inhaling welding fumes.
- Never look at the arc without proper eye protection.
- Allow the welded work to cool before handling it with tongs.
- Keep a fire extinguisher nearby in case of sparks or flames.
Step 1: Prepare the Workplace
Clear the work bench and secure the metal piece in the bench vice. Ensure the metal is clean and free from rust, oil, paint, or dirt. Use the wire brush or scraper to clean the area to be welded thoroughly.
Step 2: Mark and Position the Work
Measure and mark the position where the weld will be made using a scriber and steel rule. Use a try square to ensure the markings are straight and accurate. Position the metal so that the joint to be welded is easily accessible.
Step 3: Set Up the Welding Machine
Select the appropriate electrode (E6013 is commonly used for general sheet metal work). Insert the electrode into the electrode holder. Set the correct current range for the electrode size—typically 50–80 amperes for a 2.5mm electrode. Connect the earth clamp securely to the workpiece.
Step 4: Strike the Arc
Hold the electrode at an angle of about 70–80 degrees to the workpiece. Lower your welding shield and touch the electrode tip to the metal to create the arc. This is called striking. Maintain a short arc length (about the diameter of the electrode) for good penetration.
Step 5: Form the Weld Pool
Allow the heat of the arc to melt the base metal and form a small pool of molten metal. This is the weld pool. The pool should be small and controllable at first. Move the electrode slowly along the marked line while maintaining the arc.
Step 6: Produce the Straight Bead
Move the electrode in a straight line at a steady speed. The speed of travel determines the width and height of the bead:
- Too fast: Produces a narrow, weak bead with poor penetration.
- Too slow: Produces a wide, bumpy bead that may burn through the metal.
- Correct speed: Produces a uniform bead with slight reinforcement above the surface.
Maintain a consistent arc length and electrode angle throughout the pass. The completed bead should appear smooth, regular, and free from defects like spatter, pores, or cracks.
Step 7: Clean the Weld
After welding, allow the work to cool slightly. Use the chipping hammer to remove the slag covering the weld. Then use the wire brush to clean the weld bead until it is smooth and shiny. Inspect the bead for uniformity and quality.
- Porosity: Small holes in the weld caused by contaminated metal or incorrect arc length.
- Spatter: Tiny metal droplets scattered around the weld caused by excessive current or long arc length.
- Irregular bead: Caused by unsteady hand movement or inconsistent travel speed.
- Insufficient penetration: The weld does not reach the root of the joint, weakening the joint.
In Tanzania, skilled plumbers and metal workers who can produce quality welds are in demand for constructing water tanks, repairing hand pumps, and fabricating gutters for buildings. For example, a plumber in Mwanza may need to weld a straight bead to seal a joint on a rainwater collection tank being installed at a local school, ensuring the tank holds water without leaking. This skill also enables small business owners to offer welding services for agricultural tools, doors, and window grills in their communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Inspect the machine, cable, and electrode holder.
- Interpret working drawing
- Prepare welding materials
- Select type and size of electrode
- Set recommended current
- Weld a work piece
- Maintain electrode angle and arc length
- Control electrode travel speed along the joint.
- Inspect for weld defects
- Clean work piece
- Clean tools and equipment and store them in a safe place
Tathmini ya matokeo
Welding straight bead performed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used:
- The student should explain different ways of welding straight beads by arc welding
Principles: The student should explain the principles of: - Welding straight bead by arc welding Theories: The student should explain: -
- Importance of welding straight bead
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while welding straight beads by arc welding
- First aid
Swali
What is a straight bead in arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado