Mada za sehemu hiiPerforming arc weldingMada 6
Performing Corner Joints
A corner joint is a type of welded joint where two metal pieces are joined together at right angles (90°), forming the shape of an "L". Corner joints are commonly used in plumbing and pipe fitting to create framework structures, brackets, and support stands. In arc welding, the corner joint is one of the fundamental joint configurations that every pipe fitter must master.
Before starting any welding work, gather all the necessary tools and equipment:
- Welding machine (arc welder)
- Welding electrodes (appropriate size for the metal thickness)
- Welding tongs (to hold hot electrodes)
- Chipping hammer (to remove slag after welding)
- Wire brush (for cleaning the weld area)
- Shield and helmet (for eye and face protection)
- Leather gloves and apron (for body protection)
- Safety boots (for foot protection)
- Workbench and bench vice (to hold workpieces securely)
- Try square (to check right angles)
- Steel rule or tape measure (for measuring)
- Hacksaw (for cutting metal)
- Scribe (for marking)
- Ball pein hammer (for shaping metal)
- Centre punch (for marking drill points)
- Shear machine (for cutting sheet metal)
Safety is paramount when performing arc welding. Always follow these precautions:
- Wear proper personal protective equipment (PPE) at all times, including welding shield, gloves, apron, and safety boots
- Ensure the welding area is clear of flammable materials
- Check that the welding machine is properly grounded
- Keep the welding tongs and leads away from hot surfaces
- Never look at the welding arc without proper eye protection
- Allow the welded piece to cool before handling it
- Keep a fire extinguisher nearby
- Work in a well-ventilated area to avoid breathing harmful fumes
Step 1: Preparation and Measurement
- Determine the required dimensions of your corner joint
- Measure and mark the metal pieces using a steel rule and scribe
- Use the try square to ensure your marks are at exact right angles
Step 2: Cutting the Material
- Cut the metal pieces to the marked dimensions using a hacksaw or shear machine
- Ensure the cuts are clean and straight
- Remove any burrs or sharp edges using a file
Step 3: Fitting the Joint
- Place the two metal pieces on the workbench in an L-shape position
- Use a bench vice to hold the pieces firmly in place
- Check the fit with a try square to ensure a true 90° angle
- Make any necessary adjustments before welding
Step 4: Welding the Corner Joint
- Set the welding machine to the appropriate current for your electrode size
- Strike an arc at the root of the joint (where the two pieces meet)
- Move the electrode along the joint in a steady, uniform motion
- Create a weld bead that penetrates both pieces
- Continue welding from the root to the top of the joint
- Allow the weld to cool slightly before moving the workpiece
Step 5: Cleaning the Weld
- Use the chipping hammer to remove slag from the weld bead
- Clean the weld thoroughly with a wire brush
- Inspect the weld for uniformity and penetration
Step 6: Final Inspection
- Check the joint with a try square to ensure it remains at 90°
- Examine the weld for defects such as cracks, porosity, or incomplete fusion
- File any sharp edges or spatter from the finished joint
A plumber needs to create a support bracket for a water tank. The bracket requires two pieces of 3mm thick mild steel, each 200mm long, joined at a right angle.
Solution:
- Measure: Mark 200mm on each piece of steel using a steel rule
- Cut: Cut both pieces to length with a hacksaw
- Fit: Clamp both pieces in the bench vice so they form a 90° corner
- Weld: Use a 3.2mm electrode at approximately 100-120 amps to weld the joint
- Clean: Chip off slag and brush the weld clean
- Inspect: Verify the angle is still 90° using a try square
The result is a strong corner joint capable of supporting the water tank.
- Incomplete penetration — failing to melt the root of the joint
- Porosity — gas pockets in the weld caused by contamination
- Cracks — usually caused by rapid cooling or improper electrode selection
- Excessive spatter — caused by too high current or incorrect arc length
In Tanzania, corner joints are used extensively when fabricating water tank stands, gutter supports, and door hinges for buildings. For example, a local handyman in Dar es Salaam performing home repairs would need to weld a corner joint when constructing a stand for a 10,000-litre water tank, ensuring the structure can safely support the weight of the full tank.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Inspect the machine, cable, and electrode holder
- Interpret working drawings
- Prepare welding materials
- Select type and size of the electrode
- Set recommended current
- Weld and make a corner joint
- Maintain electrode angle and arc length
- Control electrode travel speed along the joint.
- Inspect for weld defects
- Clean work piece
- Clean tools and equipment
- Store tools, and equipment in a safe place
Tathmini ya matokeo
Corner joints performed as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used:
- The student should explain different ways of performing corner joints by arc welding
Principles: The student should explain the principles of: -
- Performing corner joint by arc welding
Theories: The student should explain: -
- Uses of chipping hammer
- Function of corner joint.
- Weld symbols.
- Angle of electrode.
- Different positions of welding.
- Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing corner joint
- First aid
Swali
What is a corner joint in arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado