Mada za sehemu hiiPerforming hand hacksaw cuttingMada 2
- Performing straight sawing
- Performing angular sawing
Straight Sawing with a Hacksaw
Straight sawing is the process of cutting metal or other materials using a hacksaw to divide a workpiece into parts along a straight line. This skill is fundamental in plumbing and pipe fitting because accurate straight cuts are needed when preparing pipes, fittings, and metal components for installation.
Hand sawing is the action of cutting different types of solid materials such as metal, wood, and plastic using a hand-held saw. For metal cutting, a special tool called a hacksaw is used. The hacksaw has a thin blade with sharp teeth designed specifically to cut through metal, which is denser and harder than wood.
Before performing straight sawing, gather the following tools:
- Hacksaw frame and blade
- Steel rule
- Scriber (for marking)
- Centre punch
- Back square
- Hammer
- Bench vice
- Tape measure
- PPE (Personal Protective Equipment) including gloves and safety glasses
- Marking pen or pencil
A hacksaw consists of three main parts:
- Blade – a thin narrow steel band with sharp teeth along one edge and two pin holes at the ends
- Frame – holds the blade in position
- Handle – provides grip for controlling the saw
There are two main types of hacksaw frames:
- Solid frames – can only hold one standard length of blade
- Adjustable frames (flat type) – can accommodate different standard lengths of blades (250mm and 300mm)
For better results, use a frame with rigid construction as it provides better grip and control while sawing.
Hacksaw blades are made from low alloy steel or high-speed steel. The two main types are:
- All-hard blades – the full blade is hardened between the pin holes, making them rigid and suitable for straight cuts
- Flexible blades – only the teeth are hardened, allowing flexibility for cutting along curved lines
The pitch is the distance between adjacent teeth. Blades are specified by length, pitch, and type. The most commonly used pitch is 1.4 mm (18 teeth per 25 mm), which works well for general metal cutting.
Use the following guide to select the right pitch:
- Coarse pitch (14 teeth per 25 mm / 1.8 mm) – best for soft materials like aluminum or copper
- Medium pitch (18 teeth per 25 mm / 1.4 mm) – suitable for general purpose cutting
- Fine pitch (24 or 32 teeth per 25 mm) – best for hard materials and thin sections like sheet metal or pipes
Important rule: When cutting thin material or pipe, the pitch must be fine enough so that at least two teeth are always engaged in the work.
Follow these steps to fit a hacksaw blade properly:
- Select the correct blade for the material to be cut
- Mount the blade by hooking the pin holes over the pins at the end of the frame and at the handle
- The teeth must point away from the handle – the saw cuts only on the forward stroke
- Take up tension with the wing nut, then turn it two more full turns
- Do not over-tighten – this can break the pins or bend the frame
- A new blade stretches slightly, so tighten it again after the first few strokes
Follow these implementation steps to perform straight cutting:
- Interpret the working drawing – understand what needs to be cut and the required dimensions
- Select working tools – gather all required tools
- Mark the workpiece – use a steel rule, scriber, and centre punch to mark the cutting line clearly on the metal surface
- Clamp the workpiece – secure it firmly in a vice, positioning the cut as close to the vice as possible to reduce vibration
- Position yourself correctly – if right-handed, cut on the right-hand side of the vice; if left-handed, cut on the left-hand side
- Guide the blade – use your thumb to guide the blade at the start of the cut
- Apply constant pressure – maintain even pressure on the forward stroke only; lift slightly on the return stroke
- Control the speed – use the whole length of the blade at about 40 to 50 strokes per minute
- Support the piece – when the blade almost cuts through, support the piece with your hand to prevent it from dropping
Always observe these safety precautions:
- Never test blade sharpness by running your finger across the teeth
- Store the hacksaw where you will not accidentally grasp the teeth
- The burr on cut surfaces is sharp and can cause serious cuts
- Never wipe chips away with your bare hand
- Cut on the correct side of the vice to prevent injury if the blade breaks
A plumber needs to cut a mild steel flat bar (5 mm × 70 mm × 200 mm) into five equal parts along a straight line.
Solution:
- Measure and mark the bar at every 40 mm (200 mm ÷ 5 = 40 mm) using a steel rule and scriber
- Select an 18 teeth per 25 mm blade (suitable for mild steel)
- Clamp the bar firmly in the vice with the first mark positioned just above the vice jaws
- Start sawing at the first mark, using long even strokes
- Complete the first cut, then reposition for each subsequent cut
- The result is five equal pieces, each 40 mm long
In Tanzania, a plumber working in Dar es Salaam or Mwanza uses straight sawing skills daily when installing water pipes in homes and buildings. For example, when fitting a water tank stand, the plumber must cut galvanized steel pipes (50 mm diameter) into specific lengths to create the frame structure — cutting each pipe to the exact measurement ensures the stand is stable and level, which is essential for the tank's safety and proper water pressure.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings.
- Identify tools.
- Select materials.
- Clamp the work piece on a bench vice.
- Take measurements.
- Mark work piece
- Perform straight sawing
- Clean work area and work piece
- Store work piece and tools in a safe place 24.
Tathmini ya matokeo
Straight sawing performed conforms to given technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of:
- Performing straight sawing
Principles: The student should explain principles of:
- Performing straight sawing
Theories: The student should explain: -
- Straight sawing
- Types of hacksaws and their main parts.
- Different types of hacksaw blades.
- Properties of materials. (Ferrous and non-ferrous metal)
- Types of materials used to manufacture blade
Detailed knowledge about:
- Safety precautions while performing straight sawing
- Waste disposal First aid
Swali
Which of the following tools is NOT required when performing straight sawing with a hacksaw?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado