Mada za sehemu hiiPerforming hand hacksaw cuttingMada 2
- Performing straight sawing
- Performing angular sawing
Angular Sawing in Pipe Fitting
Angular sawing is the process of cutting metal materials such as pipes at specific angles using a hacksaw. While straight sawing cuts material at 90 degrees (perpendicular to the workpiece), angular sawing cuts at different angles such as 45°, 135°, or other required angles. This skill is essential in plumbing and pipe fitting because pipes must often be joined at angles to navigate around obstacles or to create proper water flow paths.
Angular sawing is important in plumbing and pipe fitting for several reasons:
- It allows pipes to be joined at different angles for proper water flow and drainage
- It enables the creation of angled joints needed for fitting pipes around walls, corners, and other structures
- It is necessary for creating mitre joints when joining two pipes at an angle
- It helps plumbers install pipe systems that follow the layout of buildings
Before performing angular sawing, gather the following tools and equipment:
- Hacksaw with appropriate blade
- Workpiece (pipe or metal piece)
- Bench vice
- Tape measure
- Marking pen or scriber
- File (for deburring after cutting)
- Personal Protective Equipment (PPE): safety glasses, gloves
The choice of hacksaw blade affects the quality of your angular cut. Consider the following:
- For soft materials: Use coarse blade (14 teeth per 25mm)
- For hard materials: Use fine blade (24 or 32 teeth per 25mm)
- For thin materials and pipes: Use fine pitch blade so that at least two teeth are always engaged in the work
- The most commonly used pitch is 18 teeth per 25mm (1.4mm pitch)
Step 1: Interpret the Drawing
Read and understand the working drawing to know the required angle and dimensions of the cut.
Step 2: Mark the Workpiece
Using a tape measure and marking pen, measure and mark the exact position and angle where the cut will be made on the workpiece. Use a scriber for precise marking on metal surfaces.
Step 3: Select and Fit the Blade
Choose the correct blade for the material being cut. Fit the blade into the hacksaw frame with teeth pointing away from the handle. The blade cuts only on the forward stroke. Tighten the blade using the wing nut—about two full turns after initial tension.
Step 4: Clamp the Workpiece
Secure the workpiece firmly in the bench vice. Position it so that the marked line is close to the vice to minimize vibration. The workpiece should be clamped on the side opposite to your cutting direction.
Step 5: Position Your Body
Stand with your body balanced. If you are right-handed, cut on the right-hand side of the vice; if left-handed, cut on the left-hand side. This prevents injury if the blade breaks.
Step 6: Start the Cut
Use your thumb to guide the blade at the beginning of the cut. Begin with light pressure on the forward stroke.
Step 7: Maintain Steady Cutting
Apply constant pressure on the forward stroke while keeping the hacksaw level at the required angle. Use the whole length of the blade and maintain a steady rhythm of about 40 to 50 strokes per minute. Release pressure on the return stroke.
Step 8: Support the Workpiece
As the blade nearly completes the cut, support the piece with your hand to prevent it from falling and causing injury or damage.
Step 9: Finish and Deburr
After cutting, use a file to remove burrs and sharp edges from the cut surface. Smooth the edges for safe handling.
Step 10: Clean Up
Release the blade tension before storing the hacksaw. Clean the work area and return tools to their proper places.
- Never test blade sharpness with your finger—you will get cut
- Store hacksaws so that teeth are not exposed when picked up
- The burr on cut surfaces is sharp; handle carefully
- Do not wipe chips away with your hand—use a brush
- Cut on the correct side of the vice to prevent injury if blade breaks
A plumber needs to prepare a pipe section that will join two other pipes at a 45° angle. The plumber has a mild steel pipe that is 200mm long and must be cut at 45°.
Procedure:
- Measure 200mm from one end and mark with a marking pen
- Use a protractor or angle gauge to mark the 45° angle line
- Select a fine-pitch hacksaw blade (24 teeth per 25mm) suitable for cutting metal pipe
- Clamp the pipe in the vice with the marked line near the jaw
- Hold the hacksaw at 45° to the pipe axis and begin cutting
- Apply steady forward pressure while maintaining the angle
- Support the piece as the cut completes
- File the cut end to remove burrs
The result is a pipe end cut at exactly 45° ready for fitting.
| Angle | Application |
|---|---|
| 45° | Mitre joints, pipe junctions |
| 90° | Standard perpendicular joints |
| 135° | Extended angle joints |
In Tanzania, a plumber installing water pipes in a house in Dar es Salaam or Arusha frequently uses angular sawing when connecting pipes around corners or when installing gutter systems that slope away from buildings. For example, when fitting PVC or metal pipes for rainwater harvesting from a corrugated iron roof, the plumber must cut pipe sections at 45° angles to create proper joints that direct water flow efficiently into storage containers, ensuring the system handles Tanzania's seasonal rains effectively.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Identify tools.
- Select materials.
- Clamp the work piece on a bench vice.
- Take measurements.
- Mark work piece
- Perform angular sawing
- Clean the work area and work piece
- Store work piece and tools in a safe place..
Tathmini ya matokeo
Angular sawing performed conforms to given technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of:
- Performing angular sawing
Principles: The student should explain principles of:
- Performing angular sawing
Theories: The student should explain: -
- Importance of angular sawing
- Safety precautions.
- Types of angles.
Detailed knowledge about:
- Safety precautions while performing angular sawing
- Waste disposal
- First aid
Swali
Angular sawing is the process of cutting metal materials at which of the following angles using a hacksaw?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado