Mada za sehemu hiiPerforming power hacksaw cuttingMada 2
- Performing sawing a round metal
- Performing sawing a flat metal
Performing Sawing a Round Metal
Sawing a round metal involves using a hacksaw to cut cylindrical metal stock such as round bars or pipes into desired lengths or shapes. This skill is essential for plumbers who frequently work with round pipes and fittings.
- Hacksaw frame with blade
- Round metal workpiece (round bar or pipe)
- Steel rule
- Scriber
- Centre punch
- Bench vice
- Hammer
- Personal Protective Equipment (PPE)
Before starting any sawing work, observe these important safety rules:
- Do not test the sharpness of the blade by running your finger across the teeth
- Store the hacksaw where you will not accidentally grasp the teeth when picking it up
- The burr formed on the cut surface is sharp and can cause serious cuts
- Do not wipe metal chips away with your bare hand
- Cut on the correct side of the vice to prevent injury if the blade snaps
- Release tension on the blade before storing the hacksaw
1. Prepare the Workpiece
- Interpret the working drawing to understand the required dimensions
- Measure and mark the cutting line on the round metal using a steel rule and scriber
- Use a centre punch to create a small indentation at the starting point of the cut
2. Select and Fit the Blade
- Choose the correct hacksaw blade based on the material being cut
- For round metal, select a blade with appropriate pitch (18 teeth per 25mm is common for mild steel)
- Mount the blade with teeth pointing away from the handle
- Tighten the blade tension using the wing nut—about two full turns after taking up initial tension
3. Clamp the Workpiece
- Secure the round metal firmly in a bench vice
- Position the work so the marked cutting line is close to the vice jaws to minimize vibration
- Ensure the workpiece is stable and will not move during cutting
4. Perform the Sawing Action
- Hold the hacksaw handle firmly with your right hand (if right-handed)
- Use your left hand thumb to guide the blade at the starting point
- Apply constant forward pressure while keeping the saw level
- Use the full length of the blade with 40 to 50 strokes per minute
- Lift the saw slightly on the return stroke to relieve pressure
- Cut on the right-hand side of the vice if you are right-handed
5. Complete and Finish the Cut
- Support the workpiece as the blade nears completion to prevent it from dropping
- Smooth any rough edges using a file
- Clean the work area and return tools to their proper places
A plumber needs to cut a round copper pipe with 50mm diameter into two equal pieces. The following steps are followed:
- Measure 150mm from one end and mark the cutting line with a scriber
- Select an 18-teeth-per-25mm hacksaw blade suitable for soft metals like copper
- Clamp the pipe securely in the vice with the mark aligned near the jaw
- Start cutting slowly, using full blade strokes until the cut is complete
- File any burrs from the cut end before connecting fittings
- Using wrong blade pitch for the material hardness
- Applying too much pressure, which causes blade breakage
- Not using full blade length, causing uneven wear
- Cutting on the wrong side of the vice
- Failing to support the workpiece near completion
In Tanzania, a plumber working in Dar es Salaam or Arusha would use sawing skills when installing water supply systems. For example, when fitting a 50mm diameter round metal pipe to connect a water tank to a building, the plumber must accurately cut the pipe to the exact length required, ensuring proper alignment with fittings. This skill is also essential when repairing broken pipes or modifying existing plumbing systems in homes, schools, and health facilities across Tanzanian communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings.
- Select material to be cut.
- Clamp work piece.
- Adjust machine.
- Select blade teeth
- Set the right direction of blades.
- Take measurements.
- Select cutting speed.
- Operate the machine.
- Cut a round metal with a power saw.
- Use cooling media
- Check imperfections on cut surface
- Clean work place, tools and equipment.
- Store tools and equipment safely.
Tathmini ya matokeo
Sawing a round metal performed conforms to given technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain different procedures used in:
- Cutting a round metal.
Principles: The student should explain principles of:
- Sawing a round metal
Theories: The student should explain:
- Types of blades and sizes
- Types of grinding disc and sizes
- Different types of cooling media, and their applications.
- Parts of power saw, and their functions
- Types of angles.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing round metal sawing
- Waste disposal
- First aid
Swali
Which of the following is a safety rule that must be observed when using a hacksaw?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado