Mada za sehemu hiiPerforming power hacksaw cuttingMada 2
- Performing sawing a round metal
- Performing sawing a flat metal
Performing Sawing a Flat Metal
Sawing a flat metal is a fundamental bench work skill where a hacksaw is used to cut metal into required shapes and sizes. This process divides metal by cutting along straight or angled lines using a blade with sharp teeth.
The following tools are required for performing hand sawing:
- Hacksaw frame and blade
- Steel rule
- Scriber
- Centre punch
- Back square
- Hammer
- Bench vice
- Tape measure
There are two main types of hacksaw frames:
Solid frames — These provide only one standard length of blade that can be fitted. They are rigid and give good control during sawing.
Adjustable frames (flat type) — These can accommodate different standard lengths of blades (250mm and 300mm). The adjustability makes them more versatile for various cutting tasks.
For proper working, it is advisable to use frames of rigid construction because they provide better grip and control while sawing.
A hacksaw blade is a thin narrow steel band with teeth cut on one edge and two pin holes at the ends. The blade is made of either low alloy steel or high-speed steel.
Types of Hacksaw Blades
- All hard blades — The full blade is hardened between the pin holes. These are strong and durable.
- Flexible blades — Only the teeth are hardened because of their flexibility. These are useful for cutting along curved lines.
Pitch of the Blade
The pitch is the distance between adjacent teeth. Hacksaw blades are specified according to:
- Length (250mm or 300mm)
- Pitch (teeth per 25mm)
- Type
The most commonly used pitch is 1.4mm (18 teeth per 25mm). For soft materials, use coarse pitches (14 teeth per 25mm). For hard materials and thin sections like sheet metal or pipes, use finer pitches (24 or 32 teeth per 25mm) to ensure at least two teeth are always engaged in the work.
- Do not test the sharpness of the blade by running your finger across the teeth — you will get cut.
- Store the hacksaw so that you will not accidentally grasp the teeth when you pick it up.
- The burr formed on the cut surface is sharp and can cause a serious cut.
- Do not wipe the chips away with your hand.
- Cut on the right-hand side of the vice if you are right-handed, and on the left-hand side if you are left-handed. This prevents injury if the blade snaps.
- Release the tension on the blade before storing the hacksaw to prevent the frame from losing its spring.
Follow these steps to fit a blade correctly:
- Select the correct blade for the type of material to be cut.
- Mount the blade by hooking it over the pins at the end of the frame and at the handle.
- The teeth should point away from the handle. The saw cuts only on the forward stroke.
- Take up the tension with the wing nut, then turn it another two full turns.
- Do not overtighten — this could break the pins or bend the frame.
Note: A new blade stretches slightly and should be tightened after the first few strokes.
Vertical sawing cuts material from up to down to divide it into parts. Follow these implementation steps:
- Interpret the working drawing to understand the required dimensions.
- Select working tools — hacksaw, steel rule, scriber, centre punch, back square, and hammer.
- Mark the workpiece according to the drawing using the scriber and steel rule.
- Clamp the workpiece firmly in the vice and cut as close to the vice as possible. This eliminates vibration ("chatter") which could break the blade.
- Maintain constant pressure on the forward stroke to keep the cut even. Distribute your body mass evenly to stay balanced and in full control.
- Use your thumb (if right-handed) to guide the blade until it starts the cut.
- Apply enough pressure on the forward stroke to make the teeth cut. Insufficient pressure causes teeth to slide over the workpiece and become blunt.
- Lift the saw slightly on the return stroke to release pressure.
- Remember: The blade cuts only on the forward stroke.
- Use the whole length of the blade at about 40 to 50 strokes per minute.
- Cutting faster may cause enough heat to damage the temper in the teeth, blunting them.
- When nearly through, support the piece with your hand to prevent it from dropping.
Angular sawing cuts the material at different angles such as 45°, 90°, 135°, or 180°. The procedure is similar to straight cutting, but the workpiece is positioned at the required angle.
Important notes:
- If a blade breaks or becomes blunt before completing a cut, do not continue in the same cut with a new blade.
- As a blade goes blunt, the slot becomes narrower. Continuing will cause the new blade to stick and become ruined.
- If possible, rotate the work and start a new cut from the other side.
- If the material cannot be rotated, start a new cut next to the first cut.
A student has a mild steel flat bar measuring 5mm × 70mm × 200mm. The task is to cut the flat bar into five equal parts along a straight line.
Solution:
-
Determine the length of each piece: 200mm ÷ 5 = 40mm per piece.
-
Mark the workpiece: Using a steel rule and scriber, mark lines at 40mm, 80mm, 120mm, and 160mm along the 200mm length.
-
Select the blade: Since this is mild steel (soft material), select a coarse pitch blade (14 teeth per 25mm).
-
Clamp and cut: Clamp the workpiece in the vice and cut at each marked line following the straight sawing procedure.
-
Safety: Cut on the right-hand side of the vice (for right-handed student), use constant pressure, and support each piece when nearly cut through.
In Tanzania, metal workers and mechanics use hand sawing skills when fabricating or repairing metal structures such as window grills, door gates, and plumbing fixtures. For example, a local welder in Dar es Salaam cutting flat iron bars to make a gate frame would apply these sawing techniques to accurately cut the material to size before welding, ensuring the gate fits properly and lasts longer.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Select material to be cut.
- Clamp work piece.
- Adjust machine.
- Select blade teeth
- Set the right direction of blades.
- Take measurements
- Select cutting speed
- Operate the machine
- Cut a flat metal with a power saw
- Use cooling media.
- Check imperfections on the cut surface
- Clean work place, tools, and equipment.
- Store tools and equipment safely
Tathmini ya matokeo
Sawing a flat metal performed conforms to given technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain different procedures used in:
- Sawing a flat metal
Principles: The student should explain principles of:
- Sawing a flat metal
Theories: The student should explain:
- Types of metals
- Metal properties
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing sawing a flat metal
- Waste disposal
- First aid
Swali
Which of the following tools is NOT required when performing hand sawing of flat metal?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado