Mada za sehemu hiiPerforming metal filingMada 3
- Performing draw filling
- Performing longitudinal filling
- Performing cross filling
Draw Filing in Metalwork
Draw filing is a filing technique used to produce a smooth, flat surface on metal workpieces. Unlike ordinary filing where you push the file forward across the metal, draw filing involves pulling the file toward you while keeping it at right angles to the workpiece. This technique gives the artisan better control over material removal and produces a finer finish.
- To smooth rough surfaces left by coarse filing
- To flatten surfaces that are uneven
- To produce a surface ready for further finishing or assembly
- To achieve accurate dimensions on metal pieces
- Flat file (second-cut or smooth file)
- Workpiece (metal plate or bar)
- Bench vice
- Clamp or holding device
- Safety goggles
- Gloves
Step 1: Prepare the Workpiece
Secure the workpiece firmly in a bench vice. Make sure the surface to be filed is clean and free from rust, oil, or dirt. Check that the workpiece is positioned at a comfortable height for filing.
Step 2: Select the Appropriate File
Choose a second-cut file for rough smoothing or a smooth file for final finishing. The file should be clean and in good condition. If the file is clogged, use a file card to clean it.
Step 3: Position Your Body
Stand facing the workpiece with your feet shoulder-width apart. Hold the file handle in one hand and the tip of the file with the other hand. Keep your body balanced and steady.
Step 4: Perform the Draw Filing Motion
- Place the file flat on the workpiece surface
- Push the file forward slightly to engage the teeth
- Pull the file toward you while maintaining even pressure
- Keep the file perpendicular (90°) to the workpiece
- Use long, even strokes that cover the entire surface
- Lift the file on the return stroke
Step 5: Check Your Work
After several strokes, stop and examine the surface. The marks should be uniform across the entire width. If high spots remain, focus more pressure on those areas during the next passes.
- Always file across the previous marks at right angles to remove them
- Apply even pressure throughout the stroke
- Keep the file flat on the surface to avoid rounding edges
- Use the full length of the file for uniform results
- Clean the file regularly to prevent clogging
- Always wear safety goggles when filing metal
A plumber needs to smooth a cut edge of a galvanized iron pipe before fitting a coupling. The pipe end is rough after using a hacksaw.
Solution:
- Clamp the pipe securely in the bench vice
- Select a flat second-cut file
- Position the file at right angles to the pipe axis
- Draw the file toward you using long, even strokes
- Rotate the pipe slightly and repeat until the entire circumference is smooth
- Check by running your finger lightly along the edge
- Switch to a smooth file for final finishing if needed
The result is a clean, smooth pipe end ready for proper fitting insertion without damaging the coupling seal.
- Pressing too hard, which creates uneven surfaces
- Using a clogged or damaged file
- Filing in only one direction without crossing marks
- Not securing the workpiece properly
- Neglecting to wear safety equipment
In Tanzania, draw filing is used by local artisans when fabricating or repairing metal gates, window frames, and door hinges. For example, a village welder in Mbeya may use draw filing to smooth the edges of a metal gate after cutting the pieces to size, ensuring the gate opens and closes smoothly without catching on rough edges. This skill is also essential when preparing metal sheets for making water tanks or drainage pipes in building construction projects across rural and urban areas.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings.
- Select a file.
- Select the direction of filing.
- Perform draw filing on a work piece
- Take measurements
- Clean workplace, tools, and equipment
- Store tools and equipment safely
Tathmini ya matokeo
Draw filling performed conforms to given technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the procedures of:
- Performing draw filing
Principles: The student should explain principles of:
- Performing draw filing
Theories: The student should explain:
- Types of files
- Types of file cuts
- Characteristic of materials
- How to remove chips from files
- Filing technique
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing draw filing
- Waste disposal
- First aid
Swali
What is draw filing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado