Mada za sehemu hiiInstalling and repairing waste appliancesMada 6
- Fixing and repairing hand washbasin
- Fixing and repairing bathtub
- Fixing and repairing traps
- Fixing and repairing sink
- Fixing and repairing bidets
- Fixing and repairing drinking fountain
Fixing and Repairing Drinking Fountain
A drinking fountain (also called a water fountain or bubbler) is a sanitary appliance that provides a convenient and hygienic source of potable (safe drinking) water in public buildings such as schools, offices, markets, and hospitals. In Tanzania, drinking fountains are commonly installed in schools to ensure students have access to clean drinking water. This topic covers the components, types, materials, tools, installation location, and basic repair procedures for drinking fountains.
A typical drinking fountain consists of the following main parts:
- Bubbler head – the part where water springs out for drinking
- Basin or bowl – collects excess water and directs it to the drain
- Drain pipe – carries waste water to the drainage system
- Supply pipe – delivers fresh water from the main supply
- Stop valve – controls the flow of water to the fountain
- Mounting bracket – secures the fountain to the wall or floor
- Strainer or filter – removes particles from incoming water (in some models)
Understanding each component is essential for both installation and repair work.
There are two main types commonly used in Tanzania:
- Wall-mounted drinking fountain – Fixed to the wall at a comfortable height. Common in school hallways and public buildings.
- Pedestal or floor-mounted drinking fountain – Stands on the floor with a base. Suitable for outdoor areas like school playgrounds and market places.
Drinking fountains are made from materials that are durable, corrosion-resistant, and safe for drinking water:
- Stainless steel – Most common, rust-resistant, easy to clean, and durable
- Porcelain or ceramic – Often used for the basin in traditional designs
- Plastic (PVC or ABS) – Used for the body in cheaper models; lightweight but less durable
- Chrome-plated brass – Used for fittings and bubbler heads for strength and corrosion resistance
The following tools and equipment are needed for installing a drinking fountain:
- Adjustable wrench
- Drill machine with drill bits
- Hacksaw or pipe cutter
- Tape measure
- Screwdriver (flathead and Phillips)
- Spirit level
- Pipe fittings (elbows, tees, couplings)
- Related PPEs (safety gloves, safety goggles, dust mask)
When choosing where to install a drinking fountain, consider the following:
- Accessibility – Install at a height comfortable for all users, including children
- Proximity to water supply – Should be near an existing water main for easy connection
- Proximity to drainage – Must be close to a waste drain or gutter
- Lighting – Choose a well-lit area for hygiene and safety
- Clean environment – Avoid dusty or contaminated areas
- Traffic flow – Place in an area that does not block movement of people
In Tanzanian schools, drinking fountains are typically installed near classrooms, dining areas, or school compounds where students can easily access them.
Follow these steps to install a drinking fountain correctly:
Step 1: Site Selection and Marking
- Select the appropriate location following the guidelines above
- Use a tape measure to determine the correct height (typically 80–90 cm from the floor for wall-mounted fountains)
- Mark the positions for mounting holes using a pencil
Step 2: Drilling Mounting Holes
- Put on safety goggles and gloves
- Use a drill machine with appropriate drill bits to bore holes at the marked positions
- Insert wall plugs or anchors for secure mounting
Step 3: Connecting Water Supply
- Measure and cut the supply pipe to the required length using a hacksaw or pipe cutter
- Connect the pipe to the main water supply using appropriate fittings
- Install a stop valve to control water flow for future maintenance
Step 4: Connecting Drainage
- Connect the drain pipe from the fountain basin to the drainage system
- Ensure proper slope (at least 1:50) so water flows away smoothly
- Use a spirit level to check that the fountain is level
Step 5: Mounting the Fountain
- Attach the mounting bracket to the wall using screws and a screwdriver
- Hang or position the drinking fountain securely on the bracket
- Check alignment with the spirit level and adjust if necessary
Step 6: Testing
- Turn on the water supply slowly
- Check for leaks at all connections
- Test the bubbler to ensure water flows properly
- Verify that water drains correctly from the basin
When fixing or repairing a drinking fountain, identify these common problems:
| Fault | Possible Cause | Repair Procedure |
|---|---|---|
| No water flow | Blocked supply pipe or valve closed | Check stop valve; open if closed; clear any blockages in pipe |
| Weak water flow | Partially blocked strainer or low pressure | Clean or replace the strainer; check main supply pressure |
| Leaking basin | Cracked basin or loose drain connection | Replace cracked basin; tighten drain pipe connections |
| Dripping bubbler | Worn-out washer or valve seat | Replace the washer or the entire bubbler assembly |
| Rust or corrosion | Use of inferior materials | Clean affected areas; consider replacing with stainless steel parts |
A school in Morogoro needs to install a new drinking fountain in the playground. The plumber has the following requirements:
- Wall-mounted fountain
- Height from ground: 85 cm
- Distance from water main: 2.5 meters
- Distance from drain: 1.8 meters
Solution:
-
Select location – Choose a wall near the playground that is accessible to students and close to existing water and drain connections.
-
Mark height – Measure 85 cm from the floor and mark two holes 30 cm apart horizontally for the mounting bracket.
-
Drill holes – Use a 10 mm drill bit to bore holes at the marked positions.
-
Cut pipes – Cut supply pipe to 2.5 m and drain pipe to 1.8 m using appropriate tools.
-
Install – Connect supply pipe to main with stop valve, connect drain to waste pipe, mount bracket, hang fountain, and test for leaks and proper drainage.
This installation provides clean drinking water for over 500 students during break time.
In many Tanzanian schools, a properly installed and maintained drinking fountain helps reduce the spread of waterborne diseases among students. For example, a secondary school in Dodoma can serve over 1,000 students with a single functional drinking fountain, reducing the need to purchase bottled water (costing around TSh 5,000–10,000 per day for a class). Learning to install and repair these fountains also equips students with practical skills for employment in plumbing businesses or for starting their own small repair services in their communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawing
- Take measurements.
- Drilling
- Install drinking fountain.
- Repair and service drinking fountain
- Clean tools and workplace
- Store tools and equipment
- Connecting waste pipe
- Connecting water to drinking fountain
Tathmini ya matokeo
Drinking fountain fixed and repaired as per specification.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain procedures of performing installation, servicing and repairing drinking fountain.
Principles: The student should explain principles of:
- Installing drinking fountain.
Theories: The student should explain: -
- Fixing standard measurements of drinking fountain
- Different designs of drinking fountain
- Materials manufacturing drinking fountain
Detailed knowledge about:
- Safety precautions while fixing drinking fountain
- Environment requirements
Swali
Which of the following is NOT a main component of a drinking fountain?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado