Mada za sehemu hiiInstalling and maintaining above-ground drainage systemMada 3
- Installing and maintaining two pipe systems
- Installing and maintaining single stack system
- Installing and maintaining one pipe system
A one pipe drainage system is a sanitary pipe work system where both soil (toilet waste) and waste (from basins, sinks, showers) are discharged through a single vertical pipe called a soil and waste stack. This system is commonly used in buildings where efficiency and simplicity are important.
In a one pipe system, all waste water from toilets, wash basins, sinks, and showers flows through one main vertical pipe to the underground drainage. The system uses:
- Soil stack – carries toilet waste
- Waste stack – carries water from basins, sinks, and showers
- Ventilation pipe – allows air to enter the system, preventing siphonage and bad smells
The system is called "one pipe" because a single stack can serve multiple fixtures, making installation simpler and less expensive than separate pipe systems.
Common Pipe Sizes (for above-ground drainage)
| Fixture | Minimum pipe diameter |
|---|---|
| Wash basin | 32 mm |
| Sink | 38 mm (1.5 inches) |
| Shower | 40 mm |
| Toilet (soil pipe) | 100 mm (4 inches) |
Common Materials
- PVC (Polyvinyl Chloride) – most common, lightweight, resistant to corrosion, easy to cut and join
- Cast iron – durable, used for soil stacks, but heavy and requires special joints
- UPVC – common for domestic drainage, white or grey in colour
Before starting any installation, gather these tools:
- Pipes (PVC or as specified)
- Pipe clamps/brackets
- Spirit level
- Marking pen or chalk
- Adjustable wrench
- Hacksaw (for cutting pipes)
- Tape measure
- Screwdriver
- PPE: safety gloves, safety boots, safety goggles
1. Planning and Marking
- Read the building plan to identify where fixtures will be placed
- Mark the positions of the soil stack and waste stack on the wall using a spirit level to ensure vertical alignment
- Mark the positions for pipe clamps along the wall
2. Cutting the Pipes
- Measure the required length using a tape measure
- Mark the cutting point with a chalk or mark pen
- Cut the pipe squarely using a hacksaw
- Remove any burrs (rough edges) from the cut end using a file or sandpaper
3. Assembling the Pipe System
- Connect pipes using appropriate fittings (elbows, tees, junctions)
- Ensure joints are tight and properly glued (for PVC)
- Install pipe clamps every 1.2 to 1.5 metres to support the pipes
4. Ensuring Proper Fall
- All horizontal pipes must have a slight fall (slope) towards the drain
- The recommended fall is 1:50 to 1:40 (for every 50-40 mm horizontal, drop 1 mm vertical)
- Use a spirit level to check the fall
5. Connecting to Fixtures
- Connect the soil pipe to the toilet pan
- Connect waste pipes from basins, sinks, and showers to the waste stack
- Use traps (U-bends) below each fixture to prevent odours
6. Testing the Installation
- Run water through each fixture
- Check for leaks at all joints
- Ensure water flows freely without blockage
- Check for leaks regularly, especially at joints
- Clear blockages using a plunger or drain snake
- Inspect clamps to ensure pipes remain properly supported
- Clean traps to prevent buildup of debris and bad smells
A school toilet block needs a new one pipe drainage system. The plumber must install a 100 mm soil stack to serve two toilets, and a 40 mm waste stack to serve two wash basins.
Step 1: Measure and mark the positions for the soil stack (near the toilets) and the waste stack (near the wash basins).
Step 2: Cut a 3-metre length of 100 mm PVC pipe for the soil stack. Use a hacksaw and smooth the edges.
Step 3: Install pipe clamps every 1.5 metres along the wall to hold the soil stack vertical. Check with a spirit level.
Step 4: Connect the 40 mm waste pipe from each wash basin to the waste stack using a tee junction.
Step 5: Connect the soil pipe to the toilet pan and ensure a proper seal.
Step 6: Test by flushing the toilets and running water in the basins. Check for leaks.
- Always wear safety gloves and safety boots when handling pipes and tools
- Use safety goggles when cutting pipes
- Ensure the work area is clean and free of obstacles
- Turn off water supply before connecting new pipes to existing systems
In Tanzania, a one pipe drainage system is commonly used in household latrines and school toilets. For example, when building a new pit latrine at home, a plumber uses a 100 mm PVC pipe to connect the toilet pan to the pit, while also connecting the hand-washing basin to the same stack. This single system saves material costs and makes maintenance easier, as all waste flows through one main pipe that can be checked and cleared when blocked.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawing layout.
- Take measurements
- Install, service, and repair the above one pipe system.
- Join soil and waste stocks
- Join trap ventilation
- Perform drainage testing
- Store tools and equipment in a safe place
Tathmini ya matokeo
One pipe system was installed and maintained as per the specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain: -
- How to install and maintain one pipe system.
Principles: The student should explain the principles of:
- Installing one pipe system
Theories: The student should explain: -
- Importance of one pipe system.
- Tools used for installation
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while maintaining one pipe system.
- First aid
Swali
What is the main characteristic of a one pipe drainage system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado