Mada za sehemu hiiPerforming turningMada 3
- Performing parallel turning
- Performing taper turning
- Performing knurling
Parallel turning is a fundamental lathe machining operation where a cylindrical surface is produced along the entire length of a workpiece, maintaining a constant diameter from start to finish. This technique is essential for creating shafts, pins, and other cylindrical components used in vehicle repair and manufacturing.
Parallel turning, also called straight turning, is the process of removing material from a cylindrical workpiece to produce a uniform diameter along its length. The cutting tool moves parallel to the axis of the workpiece, creating a straight, even surface with consistent dimensions throughout.
Parallel turning is used to:
- Produce accurate cylindrical shafts and spindles
- Reduce the diameter of workpiece to required dimensions
- Create bearing surfaces
- Prepare metal for further operations like threading or fitting
Before performing parallel turning, ensure the following are available:
- Lathe machine with accessories
- Centre drill
- Steel rule
- Scriber
- Cutting tools (right-hand turn tool)
- Vernier calliper
- Depth gauge
- Hacksaw frame
- Cotton gloves
- Safety goggles and other safety gears
Step 1: Preparation of Workpiece
- Select the appropriate workpiece (mild steel round bar is commonly used for practice)
- Measure the initial diameter using a vernier calliper
- Mark the length to be turned using a scriber and steel rule
Step 2: Setting Up the Lathe
- Mount the workpiece securely in the three-jaw chuck
- Ensure the workpiece rotates true (run-out should be minimal)
- Select the appropriate cutting tool (right-hand turning tool for parallel turning)
- Mount the tool in the tool post at the correct height (centre height)
- Set the tool so the cutting edge is at workpiece centre
Step 3: Setting the Cutting Parameters
- Select suitable spindle speed based on workpiece material and diameter
- Set the feed rate (longitudinal feed for parallel turning)
- Calculate cutting speed using the formula:
Cutting Speed (m/min)=1000π×D×N
Where:
- D = diameter of workpiece in mm
- N = spindle speed in revolutions per minute (rpm)
Step 4: Performing the Cutting Operation
- Start the lathe and allow the workpiece to reach full speed
- Engage the automatic feed
- Make light cuts to achieve the desired diameter
- Take multiple passes (roughing and finishing cuts)
- Stop the lathe and measure using vernier calliper
- Continue until required diameter is achieved
Step 5: Checking the Workpiece
- Measure the diameter at several points along the length
- Verify that the diameter is consistent throughout
- The workpiece should be truly cylindrical
A mild steel workpiece with diameter 25 mm is to be turned to 20 mm diameter on a lathe running at 500 rpm.
Given:
- Initial diameter (D₁) = 25 mm
- Final diameter (D₂) = 20 mm
- Spindle speed (N) = 500 rpm
Calculate the cutting speed:
Cutting Speed=1000π×25×500=10003.142×25×500
Cutting Speed=39.28 m/min
Calculate the depth of cut for one pass:
Depth of cut = (D₁ - D₂) ÷ 2 = (25 - 20) ÷ 2 = 2.5 mm
- Always wear safety goggles when operating the lathe
- Remove loose clothing and secure long hair
- Never wear cotton gloves while operating rotating machinery
- Ensure workpiece is securely mounted before starting
- Keep hands away from rotating workpieces
- Use appropriate tool rest clearance
- Stop the machine before taking measurements
- Report any malfunction immediately
- Tapered workpiece: caused by tool not set at centre height
- Grooved surface: caused by dull cutting tool
- Oversized diameter: caused by incorrect measurements or tool feed
- Chatter marks: caused by loose tool or workpiece, or incorrect speed
In Tanzania, parallel turning skills are directly applied at vehicle repair workshops and small-scale engineering shops found in towns like Arusha, Mwanza, and Dodoma. A mechanic can use a lathe to machine a worn vehicle shaft or axle to its proper dimensions, saving the cost of buying new parts. For instance, reworking a 30 mm diameter drive shaft to specification at a local workshop may cost around TSh 15,000–25,000, compared to TSh 80,000 or more for a new replacement part.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools and equipment
- Select proper materials and tools
- Take measurements
- Cut the material to dimensions
- Select speed, feed and depth of cut
- Face workpiece
- Centre drill workpiece
- Perform rough turning
- Perform turning to finish
- Observe safety precautions
- Clean tools, equipment, and workplace
- Store tools and equipment
Tathmini ya matokeo
Machined workpiece conforms to technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Perform parallel turning on a lathe machine
Principles — the student should explain the principles of:
- Performing parallel turning
Theories — the student should explain:
- The procedure for performing parallel turning
Circumstantial knowledge — detailed knowledge about:
- Observing safety precautions while performing parallel turning
- Safe handling of work tools, equipment and workpiece
Swali
What is the main purpose of performing parallel turning on a lathe?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado