Mada za sehemu hiiPerforming boringMada 2
- Performing drilling
- Performing reaming
Reaming is a finishing operation performed on a lathe machine to enlarge and smooth a previously drilled or bored hole to achieve a precise size and better surface finish. It removes only a small amount of material, typically between 0.1 mm and 0.5 mm, from the hole walls.
The main purposes of reaming are:
- To achieve accurate hole diameter — reamers are manufactured to specific sizes and produce holes within tight tolerances.
- To improve surface finish — reaming produces a smoother, more refined surface than drilling or boring alone.
- To correct slight misalignment — it can straighten holes that are slightly off-center.
- To create precise fitting surfaces — this is essential when parts must fit together tightly in engine assemblies, transmissions, and other mechanical systems.
Hand Reamers
- Operated manually using a T-handle
- Used for finishing holes that do not require machine operation
- Typically used for repair work and maintenance in small workshops
Machine Reamers
- Mounted in a drill chuck or lathe tailstock
- Rotated by the machine while fed into the workpiece
- Used for production work requiring consistent results
- More efficient for multiple holes
Step 1: Prepare the workpiece
- Secure the workpiece firmly in the lathe chuck or collet
- Ensure the previously drilled or bored hole is clean and free of chips
Step 2: Select the correct reamer
- Choose a reamer of the desired final diameter
- Ensure the reamer type matches the material being worked
Step 3: Set the correct speed
- Use a slower speed than that used for drilling
- Typical reaming speed: 10–15 m/min for steel
- Excessive speed causes overheating and poor finish
Step 4: Apply cutting fluid
- Lubricate the reamer with appropriate cutting oil
- This reduces friction and heat buildup
- It also improves surface finish and extends reamer life
Step 5: Perform the reaming operation
- Start the lathe and allow the reamer to reach full speed
- Feed the reamer slowly and steadily into the hole
- Do not reverse the rotation while withdrawing the reamer — this damages the cutting edges
- Maintain a consistent feed rate throughout
Step 6: Measure the finished hole
- Use a vernier calliper or gauge to verify the diameter
- Check that the hole meets the required specifications
- Always wear safety clear glasses to protect eyes from flying chips
- Wear safety boots and avoid loose clothing
- Use cotton gloves when handling the workpiece, but remove them when operating the machine
- Ensure the reamer is securely held in the chuck before starting
- Never stop the lathe abruptly while the reamer is in the hole
A technician needs to finish a hole for a bearing fit in a cylinder block. The hole has been drilled to 15.0 mm diameter, but the bearing requires a hole of 15.5 mm with a smooth finish.
Solution:
- Select a 15.5 mm machine reamer
- Set lathe speed to approximately 300 rpm (using the formula: v=1000πdn, where v = 12 m/min)
- Apply cutting oil to the reamer and hole
- Feed the reamer steadily into the hole at 0.1 mm/rev feed rate
- Withdraw the reamer while maintaining rotation in the forward direction
- Measure the hole with a 15.5 mm gauge pin — it should slide through with slight resistance
The finished hole is now ready for the bearing installation.
In Tanzania, reaming is commonly used in motor vehicle repair shops when fitting new engine bearings, rebuilding brake drums, or repairing transmission housings. When a mechanic at a garage in Dar es Salaam or Arusha needs to replace a worn bearing seat in an engine block, they will bore the hole first and then use a reamer to achieve the precise diameter needed for the new bearing — this ensures the bearing fits tightly and operates safely, extending the engine's lifespan and preventing costly breakdowns.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools and equipment
- Perform boring
- Deburr workpiece
- Observe safety precautions
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Workpiece bored according to given technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Perform reaming on a lathe machine
Principles — the student should explain the principles of:
- Performing reaming
Theories — the student should explain:
- The procedure for carrying out reaming
Circumstantial knowledge — detailed knowledge about:
- Observing safety requirements while boring on the lathe machine
- Safe handling of work tools, equipment, and workpiece
Swali
What is the primary purpose of performing reaming on a lathe machine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado