Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Performing drilling on a bench drilling machine
- Counterboring drilled holes
Hand drilling is a process of creating holes in metal, wood, or plastic using a portable drilling machine that is held and operated by hand. This skill is essential in motor vehicle mechanics for making holes in plates when repairing or fabricating vehicle components.
A hand drill is a small portable drilling machine that resembles a breast drill. It is designed to be held and operated by hand. The drill bit rotates at high speed and is pressed into the workpiece to create a cylindrical hole that can pass partially or completely through the material.
Cordless Drill
A cordless drill is electrical equipment operated by a battery fitted inside it. It is not connected to the electricity mains, making it more portable and convenient for work in areas without easy access to power.
Electric Drill Machine
An electric drill machine is a power tool used to create cylindrical holes in a workpiece. The tool bit is rotated at high speed and pressed into the workpiece to create holes.
The following tools and materials are needed for hand drilling:
- Tools/Equipment: Oil can, work bench, drill bits, bench vice, drill machine
- Materials: Oil, cotton waste, workpiece (plate to be drilled), drill bits
- Safety Gears: Safety boots, overall, leather gloves, safety goggles
Before performing hand drilling, always observe these safety precautions:
- Examine the machine and make sure it is in good working order before using it.
- Check the power supply cable and plug for damage and replace if necessary. Do not repair damaged cables.
- Keep the power supply cable clear of the working area.
- Hold the machine at right angles (90°) to the sheet.
- Use the correct size chuck key.
- Secure the chuck key to the lead with tape or any other type of non-conducting material. Make sure it does not cut into the insulation of the power lead.
- Hold the drilling machine securely before pressing the trigger switch.
- Use wooden strips underneath your workpiece to prevent damage to the workbench.
- Handle the machine carefully and place it on the bench in such a way that it can't be knocked down, and that nobody can trip over the power lead.
- Clamp small workpieces in a vice or on the workbench before drilling them.
-
Prepare the workpiece: Mark the position where the hole will be drilled on the plate using a scriber and try square. Use a centre punch to create a small indentation at the marked point to guide the drill bit.
-
Select the drill bit: Choose the correct size drill bit for the hole you need to make. The size of the drill bit determines the diameter of the hole.
-
Install the drill bit: Insert the drill bit into the chuck and tighten securely using the chuck key.
-
Secure the workpiece: Clamp the workpiece firmly to the workbench or in a vice. Place wooden strips underneath to protect the workbench surface.
-
Position the drill: Hold the drilling machine at 90° to the workpiece surface. Align the drill bit with the centre punch mark.
-
Start drilling: Press the trigger switch and apply steady, even pressure. Let the drill bit do the work—do not force it.
-
Complete the hole: Continue drilling until the bit passes completely through the workpiece for a through-hole, or to the required depth for a blind hole.
-
Finish: Release the trigger and wait for the drill bit to stop completely before removing it from the hole.
A student needs to practice hand drilling on a flat bar of 100mm × 100mm × 10mm. The student should drill three holes with diameters of 3mm, 6mm, and 9mm.
Procedure:
- Mark three positions on the plate, ensuring they are evenly spaced
- Centre punch each position
- Start with the smallest drill bit (3mm) and drill the first hole
- Change to the 6mm drill bit and drill the second hole
- Change to the 9mm drill bit and drill the third hole
- Clean the workpiece with cotton waste and apply oil to prevent rust
This practice helps students develop control and accuracy in handling different drill bit sizes.
In Tanzania, hand drilling skills are used in local workshops and garage settings when repairing vehicle body panels, fabricating custom brackets, or creating holes for bolt installations. For example, a mechanic in Arusha might use a hand drill to create holes in a damaged truck body panel before installing rivets to secure a replacement section, allowing the vehicle to be repaired without needing expensive imported parts.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Select tools, equipment, and materials
- Mark workpiece
- Cut workpiece to size
- Perform drilling
- Perform reaming
- Observe safety precautions
- Clean tools, equipment, and work place
- Store tools, equipment and workpiece
Tathmini ya matokeo
Drilled hole conforms to technical specifications.
Tathmini ya maarifa
Method used — the student should explain how to:
- Perform drilling process
- Perform reaming
- Calculate drill size and drilling speed
Principles — the student should explain the principles of:
- Drilling
- Selecting of drilling speed
Theories — the student should explain:
- Drilling procedure
- Importance of coolant in drilling process
- Materials used to manufacture drill bits
- Drill bit cutting angles
Circumstantial knowledge — detailed knowledge about:
- Safety precautions while performing the task
- Safe handling of tools and equipment
- Waste disposal
Swali
Which of the following is the correct definition of hand drilling?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado