Mada za sehemu hiiServicing drum brakesMada 5
- Checking brake drum
- Relining drum brake shoes
- Adjusting drum brakes
- Removing air from the system
- Performing facing of brake drums
Relining drum brake shoes is the process of replacing the worn friction material (brake lining) on brake shoes with new lining material. This is one of the most common service operations for drum brake systems and is essential for maintaining vehicle safety.
A brake lining is a friction material attached to the surface of brake shoes in drum brake systems. When the brakes are applied, the brake shoe presses against the rotating brake drum, and the friction between the lining and the drum creates the stopping force.
Why brake linings wear out: The braking system works because of friction between the brake shoe and the drum. During normal driving, this friction causes the brake lining to wear down gradually. Over time, the lining becomes thin and must be replaced.
Consequences of worn linings: If brake linings are not replaced before they wear completely, metal-on-metal contact occurs. This damages both the brake shoes and the drum, leading to costly repairs and reduced braking efficiency.
Brake shoes should be relined when the friction material has worn down to within 1/32 inch (0.8 mm) of the rivets. Most brake drums have an inspection hole that allows you to check the remaining lining thickness. Always refer to the vehicle service manual for the exact specification.
There are two main methods for relining brake shoes:
Rivet Method
In this method, the brake lining is attached to the brake shoe using rivets. The rivets pass through both the lining and the shoe, creating a strong mechanical bond. This method is traditional and widely used.
Compound Bond (Adhesive) Method
In this method, the brake lining is glued to the shoe using a special heat-resistant adhesive compound. Both the lining and the shoe are cleaned thoroughly, then the adhesive is applied to bond them together.
- Pop rivet gun and rivets (for rivet method) or adhesive compound (for bond method)
- Brake lining material
- Brake shoe
- Bench vice
- Rivets
- Sandpaper
- Vernier caliper
- Service manual
- Safety glasses, dust mask, gloves, overall, safety boots
-
Safety first — Wear safety glasses, dust mask, gloves, and safety boots throughout the procedure.
-
Remove the brake drum — Follow the standard procedure: loosen wheel nuts, jack the vehicle, remove the wheel, then remove the brake drum.
-
Remove the brake shoes — Disconnect the brake shoes from the wheel cylinder and remove them from the backing plate.
-
Inspect and measure — Use a vernier caliper to measure the thickness of the brake lining. Check if it is worn beyond the service limit (0.8 mm from rivets).
-
Remove old lining — Drill out the old rivets and remove the worn brake lining from the shoe.
-
Clean the shoe — Clean the top surface of the brake shoe and clear any debris from the rivet holes.
-
Clamp the shoe — Secure the brake shoe in a bench vice, ensuring it is held firmly.
-
Align the new lining — Place the new brake lining on the shoe and align the holes properly.
-
Install rivets — Insert rivets through the lining and shoe holes. Use the pop rivet gun to secure all rivets. Ensure all rivet heads are flush with the lining surface and do not protrude above it.
-
Smooth the surface — Use sandpaper to smooth any rough edges on the new lining.
-
Reassemble — Install the relined brake shoes back onto the wheel cylinder and refit the brake drum.
-
Adjust brakes — Adjust the brake shoes until they just touch the inner working drum.
-
Refit wheel and test — Refit the wheel, lower the vehicle, and test the brake performance.
- Always wear protective equipment: safety glasses, dust mask, gloves, overall, and safety boots.
- Work in a well-ventilated area to avoid inhaling brake dust.
- Ensure the vehicle is securely supported on jack stands before working underneath.
- Use appropriate tools for each step to prevent damage or injury.
A mechanic at a garage in Dar es Salaam inspects a customer's brake drum. Through the inspection hole, the lining appears very thin. Using a vernier caliper, the mechanic measures the remaining lining thickness as 1.0 mm. Since the service limit is 0.8 mm from the rivets, and the current measurement is already close to this limit, the mechanic decides to reline the brake shoes before the vehicle is returned to the customer. This prevents potential brake failure and expensive drum repairs.
In Tanzania, many small mechanic workshops in towns like Arusha, Mwanza, or Dodoma regularly service drum brakes on local vehicles such as taxis and daladala minibuses. A mechanic who knows how to properly reline drum brake shoes can offer this service to vehicle owners, ensuring their brakes are safe while earning income. For example, relining all four brake shoes on a Toyota Wish taxi might cost around TZS 80,000–120,000 including parts, providing both safety and a livelihood opportunity for the mechanic.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Remove shoes
- Remove old linings
- Fit new lining material
- Rivet / bond linings
- Grind to drum radius
- Reinstall and adjust
- Observe safety precautions
Tathmini ya matokeo
Drum brake shoes relined per specifications.
Tathmini ya maarifa
Method used — the student should explain how to reline drum brake shoes.
Principles — the student should explain the principles of:
- Friction material selection
- Drum-to-lining contact area
Theories — the student should explain:
- Riveted vs bonded linings
- Lining wear and service intervals
- Effects of glazed linings
Circumstantial knowledge — detailed knowledge about:
- Brake dust safety
- Grinding wheel safety
- Waste disposal
Swali
What is the purpose of relining drum brake shoes?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado