Mada za sehemu hiiServicing drum brakesMada 5
- Checking brake drum
- Relining drum brake shoes
- Adjusting drum brakes
- Removing air from the system
- Performing facing of brake drums
Performing Facing of Brake Drums
Brake drum facing is the process of machining the working surface of a brake drum on a lathe to restore its smoothness and correct any uneven wear. This restores proper braking performance and ensures safe vehicle operation.
Brake drum facing, also called drum machining or resurfacing, is a workshop process performed on a brake lathe to remove material from the inner working surface of a brake drum. When brake drums are used over time, their rubbing surface becomes grooved, scored, or uneven due to friction from the brake shoes. This roughness can cause:
- Reduced braking efficiency
- Noisy brakes (grinding or scraping sounds)
- Uneven wear on new brake shoes
- Vibration during braking
Facing removes a thin layer of material from the drum's surface to create a smooth, even finish that works properly with new brake linings.
Brake drums should be faced when:
- The drum surface shows visible scoring, grooves, or rust spots
- The drum has been resurfaced before and is approaching the minimum allowable diameter
- New brake shoes are being installed and the drum surface is rough
- The vehicle exhibits vibration or noise during braking
Important: Always check the manufacturer's minimum diameter specification in the service manual before machining. If the drum is already at or below the minimum diameter, it must be replaced rather than machined.
- Brake lathe (drum rotor attachment)
- Drum gauge or micrometer
- Service manual
- Silencer band
- Facing tool (cutting bit)
- Lathe coolant
- Safety glasses
- Dust mask
- Gloves
- Overall
- Safety boots
- Always wear safety glasses when operating the brake lathe
- Wear a dust mask to avoid inhaling metal particles
- Wear gloves when handling drums that may have sharp edges
- Wear safety boots for foot protection
- Ensure the work area is clean and free of oil or coolant spills
- Follow the service manual instructions for lathe operation
Step 1: Preparation
- Observe safety precautions throughout the process
- Ensure the vehicle is on a flat surface with the engine switched off
- Select all required tools and equipment
- Place wheel stoppers on wheels that are not being worked on
Step 2: Removing the Brake Drum
- Loosen the vehicle wheel nuts
- Jack the vehicle and secure it on safety stands
- Remove the wheel
- Set the underneath bed ( axle stand) for protection
- Disengage the parking brake
- Lower the brake shoe to release tension and remove the brake drum
- Inspect the drum visually for cracks, severe scoring, or damage
Step 3: Measuring the Drum
- Use a drum gauge or micrometer to measure the drum's inner diameter
- Compare the measurement with the minimum diameter specified in the service manual
- If the drum is above minimum, proceed with facing; if at or below minimum, replace the drum
Step 4: Setting Up the Lathe
- Clean the drum thoroughly to remove dirt and debris
- Mount the drum securely on the brake lathe using the proper adapters
- Install the silencer band around the drum to reduce vibration during cutting
- Select the appropriate cutting tool and install it in the tool holder
- Set the required cutting depth and spindle speed according to the service manual
Step 5: Performing the Facing Operation
- Start the lathe and allow the drum to reach full speed
- Slowly feed the cutting tool into the drum surface
- Make light, even passes across the drum surface
- Continue machining until the surface is smooth and even
- Check the diameter after each few passes to avoid over-cutting
Step 6: Finishing
- Stop the lathe and allow the drum to stop completely
- Remove the drum from the lathe
- Clean the drum to remove all metal particles and coolant
- Measure the final diameter and compare with specifications
Step 7: Refitting the Drum
- Refit the drum to the vehicle hub
- Adjust the brake shoes until they just touch the drum (as per adjustment procedure)
- Connect the parking brake
- Refit the wheel
- Remove safety stands and stoppers
- Test the brake performance
A mechanic at a garage in Arusha needs to service the rear brakes of a Toyota Hiace. The brake drum shows light scoring marks from worn brake shoes, and the vehicle owner reports a scraping sound when braking. The service manual states:
- Maximum drum diameter: 254.0 mm
- Minimum drum diameter: 252.0 mm
The mechanic measures the drum and finds it is 253.2 mm in diameter.
Calculation:
Current diameter = 253.2 mm
Minimum allowable diameter = 252.0 mm
Maximum material that can be removed = 253.2 - 252.0 = 1.2 mm
Since 1.2 mm can be safely removed and the drum surface needs only light machining (approximately 0.3-0.5 mm), the drum can be faced on the lathe. The mechanic performs the facing operation, removing about 0.4 mm of material. After finishing, the drum diameter becomes 252.8 mm, which is above the minimum of 252.0 mm. The drum is refitted, new brake shoes installed, and the braking noise is eliminated.
- Brake drum facing restores the working surface of the drum by removing a thin layer of material
- Always check the minimum diameter specification before machining
- Drums at or below minimum diameter must be replaced, not faced
- Proper mounting and use of silencer band prevents vibration and poor surface finish
- Safety equipment must be worn throughout the operation
- After facing, always adjust brake shoes to the correct clearance
In Tanzania, brake drum facing is commonly performed at vehicle service centres and mechanic workshops in cities like Dar es Salaam, Mwanza, and Dodoma. For example, a small-scale mechanic operating a workshop in Mwanza can use a brake lathe to face drums for taxis and daladala (minibuses), charging around TZS 15,000–25,000 per drum. This skill helps ensure passenger safety on Tanzania's roads, where properly functioning brakes are essential for preventing accidents, especially on mountainous routes like the Dar es Salaam to Morogoro road.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Mount drum on brake lathe
- Set silencer band
- Perform light cuts until drum is true
- Check final ID against max-spec
- Observe safety precautions
Tathmini ya matokeo
Brake drum faced within manufacturer's tolerance.
Tathmini ya maarifa
Method used — the student should explain how to face a brake drum.
Principles — the student should explain the principles of:
- Truing surfaces by light cuts
- Surface finish standards
Theories — the student should explain:
- Brake lathe operation
- Max machine spec limits
- Effects of out-of-true drum
Circumstantial knowledge — detailed knowledge about:
- Lathe safety (rotating tooling, swarf)
- Brake dust safety
- Waste disposal
Swali
What is the main purpose of performing facing on a brake drum?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado