Mada za sehemu hiiServicing disc brakesMada 3
- Replacing brake pads
- Repairing brake calliper
- Performing facing of the brake disc
Repairing Brake Calliper
A brake calliper is a vital component in a disc brake system that uses hydraulic pressure to clamp brake pads against a rotating disc, slowing or stopping the vehicle. Over time, the internal seals of a calliper can wear out, causing brake fluid leaks or reduced braking performance. Repairing a brake calliper involves disassembling it, replacing worn seals and components, and reassembling it correctly.
The main purposes of repairing a brake calliper are:
- Restore hydraulic sealing: Replace worn seals to prevent brake fluid leaks
- Ensure proper piston movement: Clean and lubricate the piston so it slides smoothly
- Maintain even braking: A properly repaired calliper ensures equal pressure on both brake pads
- Extend brake system life: Regular servicing prevents damage to other brake components
Before starting repair work, gather the following:
- Service manual for the vehicle
- Brake calliper rebuild kit (new seals and hardware)
- Brake fluid (DOT 3 or DOT 4 as specified)
- Compressed air gun
- Hand tools (socket set, wrenches, screwdrivers)
- Torque wrench
- Safety glasses, gloves, overall, and safety boots
- Clean rags and brake cleaner
- Wire brush and sandpaper
- Park the vehicle on a flat surface and switch off the engine
- Disconnect the negative battery terminal
- Wear safety glasses to protect eyes from brake dust and fluid
- Wear gloves when handling brake fluid (it can irritate skin)
- Secure the vehicle with wheel chocks before jacking
- Keep brake fluid away from paintwork — it damages paint
Step 1: Remove the Brake Calliper
- Loosen the wheel nuts while the vehicle is on the ground
- Jack up the vehicle and secure it on safety stands
- Remove the wheel to access the calliper
- Disconnect the brake hose from the calliper (have a container ready to catch fluid)
- Remove the bolts attaching the calliper to the mounting bracket
- Carefully lift the calliper off the brake disc and rotor
Step 2: Disassemble the Calliper
- Place the calliper on a clean workbench
- Remove the brake pads from the calliper
- Locate the bleeder screw and remove it
- Use a suitable tool to push the piston back into the calliper bore (this makes removal easier)
- Remove the dust boot and the inner seal from the piston groove
- Carefully remove the piston from the calliper housing
Step 3: Inspect All Components
Inspect each part for wear or damage:
| Component | What to Check |
|---|---|
| Calliper housing | Cracks, corrosion, scoring marks |
| Piston | Scratches, wear, rust |
| Dust boot | Cracks, tears, stiffness |
| Inner seal | Wear, hardening, damage |
| Bleeder screw | Clogged or damaged threads |
Replace any worn or damaged parts with new ones from the rebuild kit.
Step 4: Clean All Parts
- Clean the calliper housing interior with brake cleaner
- Use compressed air to dry all passages and bore
- Clean the piston with brake cleaner and a clean rag
- Do not use petroleum-based cleaners — they damage rubber seals
Step 5: Install New Seals and Reassemble
- Lubricate the new inner seal with clean brake fluid
- Install the inner seal into the piston groove (ensure it sits properly)
- Install the dust boot onto the piston
- Insert the piston into the calliper bore carefully
- Seat the dust boot into the calliper housing groove
- Install the bleeder screw
- Reinstall the brake pads into the calliper
Step 6: Refit the Calliper to the Vehicle
- Position the calliper onto the mounting bracket
- Install and tighten the mounting bolts to the specified torque (refer to service manual)
- Reconnect the brake hose and tighten securely
- Refit the wheel and lower the vehicle
Step 7: Bleed the Brake System
- Fill the master cylinder reservoir with fresh brake fluid
- Bleed air from the brake system starting with the wheel farthest from the master cylinder
- Follow the sequence: right rear, left rear, right front, left front
- Check brake pedal feel — it should be firm, not spongy
Suppose a taxi driver in Dar es Salaam notices the front left wheel is overheating and the brake pedal feels spongy. Upon inspection, a mechanic finds a leaking seal in the front left brake calliper. The repair steps would be:
- Remove the front left wheel and calliper
- Disassemble and find a worn inner seal and damaged dust boot
- Replace with new parts from a rebuild kit
- Clean all components thoroughly
- Reassemble and refit the calliper
- Bleed the brake system to remove air
- Test drive — the brake pedal now feels firm and the wheel no longer overheats
- Leaking seals: Caused by wear, age, or heat damage — replace seals
- Stuck piston: Caused by corrosion or dirt — clean and lubricate or replace
- Uneven brake pad wear: Often caused by a faulty calliper not applying equal pressure
- Spongy brake pedal: Air in the system or low brake fluid — bleed the system
In Tanzania, brake calliper repair is a common service offered at local mechanic shops and roadside garages. For example, a daladala (minibus) driver in Arusha relies on properly functioning disc brakes to safely transport passengers through busy markets. When the brakes feel soft or pull to one side, a trained mechanic can rebuild the calliper using a rebuild kit costing around TSh 30,000 to 80,000, restoring safe braking without needing an expensive replacement part. This skill is valuable for small garage owners who serve taxi and daladala operators in their community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Remove caliper
- Disassemble, inspect bore and piston
- Replace seals / dust boots / piston
- Reassemble with new fluid
- Reinstall and bleed
- Observe safety precautions
Tathmini ya matokeo
Brake caliper repaired per specifications.
Tathmini ya maarifa
Method used — the student should explain how to rebuild a brake caliper.
Principles — the student should explain the principles of:
- Caliper seal sealing
- Slider mechanism
Theories — the student should explain:
- Fixed vs floating calipers
- Common failure modes
- Effects of stuck slider / piston
Circumstantial knowledge — detailed knowledge about:
- Brake fluid handling
- Compressed air safety when removing piston
- Waste disposal
Swali
What is the main purpose of repairing a brake calliper?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado