Mada za sehemu hiiServicing disc brakesMada 3
- Replacing brake pads
- Repairing brake calliper
- Performing facing of the brake disc
Performing Facing of the Brake Disc
Brake disc facing is a machining process that restores the smooth, flat surface of a brake disc by removing a thin layer of material. When brake pads rub against the disc over time, grooves, scratches, and uneven wear develop. Facing removes this damaged layer, allowing the brake pads to make proper contact and restore effective braking performance.
Brake discs become worn and damaged due to:
- Normal wear from continuous contact with brake pads
- Grooves and scoring caused by worn or contaminated brake pads
- Heat spots created during heavy braking
- Uneven surface leading to brake vibration or pulsing
- Thickness variation that reduces braking efficiency
Before performing any machining, technicians check the disc thickness against the manufacturer's minimum specification using a micrometer.
- Service manual (vehicle-specific)
- Brake lathe (bench type or on-vehicle)
- Micrometer
- Dial indicator
- Brake cleaning solution
- Safety glasses, gloves, overall, and safety boots
- Torque wrench
- Appropriate cutting tools for the lathe
- Always wear safety glasses to protect eyes from metal particles
- Wear gloves when handling brake components
- Ensure the vehicle is securely supported on jack stands before working
- Disconnect the negative battery terminal
- Keep the work area clean and free of grease and oil
- Follow the service manual specifications for all measurements
Step 1: Preparation and Inspection
- Remove the wheel and brake calliper according to the service manual
- Remove the brake disc from the hub
- Inspect the disc for cracks, severe scoring, or heat spots
- Measure the disc thickness using a micrometer at several points
- Compare measurements with the minimum thickness specification in the service manual
- If the disc is below minimum thickness, replace it rather than face it
Step 2: Setting Up the Brake Lathe
- Mount the brake disc securely on the lathe chuck or adapter
- Ensure the disc is centered properly
- Install the appropriate cutting tool
- Set the cutting depth according to the manufacturer's instructions (typically 0.2–0.5 mm per pass)
- Set the feed rate as specified in the service manual
Step 3: Performing the Facing Operation
- Start the brake lathe and allow it to reach normal speed
- Slowly feed the cutting tool into the disc surface
- Make multiple light cuts rather than one heavy cut
- Continue machining until the entire disc surface is smooth and even
- Remove any burrs or sharp edges from the disc edges
Step 4: Measuring After Machining
- Measure the disc thickness again after facing
- Ensure it is above the minimum specification
- Use a dial indicator to check disc runout (wobble)
- Runout should not exceed the manufacturer's limit (typically 0.05–0.1 mm)
Step 5: Reassembly
- Clean the machined disc thoroughly with brake cleaning solution
- Reinstall the disc on the hub
- Refit the brake calliper
- Install the wheel and torque wheel nuts to specification
- Test the vehicle and check brake operation before road use
| Measurement | Typical Specification |
|---|---|
| Minimum disc thickness | Check service manual (often 20–25 mm) |
| Maximum runout | 0.05–0.10 mm |
| Machining depth per pass | 0.2–0.5 mm |
If the disc cannot be machined to meet specifications, it must be replaced with a new one.
- Brake pedal pulsation caused by uneven disc surface
- Noise during braking from grooves in the disc
- Reduced braking efficiency from poor pad contact
- Steering wheel vibration at high speeds from disc runout
In Tanzania, many small mechanic workshops in places like Mwanza, Arusha, or along the road to Dodoma offer brake disc facing services for daladalas, taxicabs, and private vehicles. A driver whose car pulls to one side when braking—common after years of city driving—can have the brake disc faced for about TSh 15,000 to 30,000, restoring smooth braking without the cost of buying a new disc. This skill is valuable for young technicians seeking employment in these workshops.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Measure disc thickness and runout
- Mount disc on lathe
- Take light truing cuts
- Verify thickness within min-spec
- Observe safety precautions
Tathmini ya matokeo
Brake disc faced within manufacturer's tolerance.
Tathmini ya maarifa
Method used — the student should explain how to face a brake disc.
Principles — the student should explain the principles of:
- Truing both faces equally
- Minimum thickness specification
Theories — the student should explain:
- Solid vs vented vs slotted discs
- Causes of warpage
- Effects of out-of-true disc
Circumstantial knowledge — detailed knowledge about:
- Lathe safety
- Swarf handling
- Waste disposal
Swali
What is the primary purpose of performing facing on a brake disc?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado