Mada za sehemu hiiServicing hydraulic brake system componentsMada 4
- Servicing master cylinder
- Servicing wheel cylinder
- Servicing brake booster
- Performing bleeding hydraulic brake system
A hydraulic brake system is a combination of braking system components that can cause a moving vehicle to slow down or stop when the brake pedal is pressed, with the help of hydraulic fluid (brake fluid). The system converts the mechanical force you apply on the brake pedal into hydraulic pressure that pushes the brake shoes or pads against the drums or discs to stop the vehicle.
The hydraulic brake system consists of several components that work together:
Brake pedal – Located inside the vehicle, pressed by the foot to activate the brakes.
Fluid reservoir – Houses the brake fluid used in the braking system.
Brake master cylinder – Converts the mechanical energy applied at the brake pedal into hydraulic pressure.
Fluid lines – Pipes through which brake fluid circulates within the vehicle.
Drum assembly – The end part of drum-type brakes, consisting of a drum, wheel cylinder, back plate, and brake shoes.
Disc assembly – The end part of disc-type brakes, consisting of a disc rotor, callipers (with cylinder and pistons), and brake pads.
The master cylinder (also called brake main cylinder) is located in front of the brake booster. Its main function is to convert the mechanical force the driver applies on the brake pedal into hydraulic pressure needed to stop the vehicle. When the brake pedal is pressed, the piston of the master cylinder pushes to create pressure on the brake fluid. This high pressure is transmitted through the brake lines to the brake calipers or wheel cylinders at each wheel.
Types of Master Cylinder
Single circuit master cylinder – Has a single piston and reservoir. It is simple and common in older vehicles but is less safe because if the single circuit fails, there are no brakes.
Dual circuit master cylinder – Has two separate pistons and two reservoirs. Each circuit operates independently, improving safety by allowing brakes to function if one circuit fails. This is the standard in most modern vehicles.
Many modern master cylinders have a brake fluid level sensor that monitors fluid level. If fluid drops below the specified amount, the dashboard brake warning light illuminates to alert the driver.
When the master cylinder is not working correctly, there will be insufficient hydraulic pressure for the system to work efficiently.
| Fault/Symptoms | Causes/Problem | Remedies |
|---|---|---|
| Leakage of brake fluid | Corrosion of seals due to wrong fluid type; damaged reservoir or cylinder | Use correct brake fluid; perform regular checks |
| Brake fluid contamination | Damaged seals; air in the system | Replace seals and reservoir; use correct fluid; bleed brakes |
| Spongy brake pedal | Low fluid level; air in system; outdated fluid; leakage; broken spring | Check fluid level; bleed brakes; inspect for leaks; check cylinder components |
| Loss of pressure | Damaged seals; broken spring; fluid leakage | Replace worn seals; use correct fluid; bleed brakes |
| Brake warning light on | Low fluid or leakage; worn pedal; malfunction sensors | Check fluid level; inspect for damage; check sensors |
Follow these steps to diagnose why the brake warning light is on:
Materials and Tools
- Brake fluid and cotton rags
- Vehicle with brake system or teaching model
- Brake tool kit
- Wheel stoppers
- Vehicle service manual
- Safety gear (gloves, overall, safety boots, safety clear glass)
Procedure
- Select tools, equipment, and safety gear.
- Observe safety precautions.
- Open the bonnet and locate the master cylinder.
- Check the brake fluid level. If the level is low, the sensor will light the brake warning lamp. If the level is sufficient but the light is still on, the sensor may be defective.
- Check the parking brake switch. If engaged, it can cause the warning light to illuminate.
- Disengage the parking brake. If it is still illuminating, check other causes using the manufacturer's manual.
- Check the brake pressure differential sensor. If it is good, it will not illuminate the warning light without pressure on the brake pedal.
- Inspect the master cylinder and other components for corrosion, damage, or leakage.
- Rectify the problems found.
- Test to confirm there is no illumination.
- Clean the working area and tools, and collect tools as per workshop regulations.
Example Diagnosis
If a driver in Dar es Salaam notices the brake warning light glowing on the dashboard while driving, they should first check the master cylinder reservoir. If the brake fluid is below the "MIN" mark, they need to add the correct type of brake fluid (such as DOT 4). If the fluid level is normal but the light stays on, the brake fluid level sensor or the parking brake switch may be faulty and should be inspected.
In Tanzania, mechanics at local garages along the highways (such as along the Dar es Salaam to Morogoro road) regularly service master cylinders on trucks and buses that travel long distances. When a driver reports a "spongy" brake pedal, a mechanic will check the master cylinder fluid level, inspect for leaks, and bleed the brakes if air has entered the system. This ensures safe stopping for vehicles carrying passengers and goods, which is critical for road safety in our country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Diagnose master cylinder
- Rectify fault master cylinder
- Repair or replace fault master cylinder components
- Test master cylinder
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
Serviced master cylinder functions according to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to diagnose and repair or replace master cylinder
Principles: The student should explain the principles involved in Servicing master cylinder
Theories: The student should explain:
- Function of hydraulic brake system
- Construction and operation of brake master cylinder
- Classification of brake fluids
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What is the primary function of the brake master cylinder in a hydraulic brake system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado