Mada za sehemu hiiServicing hydraulic brake system componentsMada 4
- Servicing master cylinder
- Servicing wheel cylinder
- Servicing brake booster
- Performing bleeding hydraulic brake system
A brake booster is a component of the hydraulic brake system that helps amplify the force applied to the brake pedal, making it easier for the driver to stop the vehicle. It is also called a "brake servo" or "vacuum booster." Without a working brake booster, the driver would need to apply much more force on the brake pedal to stop the vehicle.
There are two main types of brake boosters used in vehicles:
Conventional (Vacuum) Brake Booster
This type uses vacuum pressure created by the engine to amplify braking force. When the brake pedal is pressed, a valve opens to allow vacuum pressure to flow into the booster, which then multiplies the driver's foot force.
Electric Brake Booster
Modern vehicles, including hybrid and electric vehicles, use an electric brake booster. Instead of relying on engine vacuum, this type uses an electric motor to generate hydraulic pressure when the driver presses the brake pedal. The electric motor is actuated by the brake pedal input and creates the necessary pressure for braking.
When you press the brake pedal in a vehicle with a conventional vacuum booster, the following happens:
- The brake pedal pushes a push rod into the booster
- A valve opens to allow vacuum pressure from the engine to enter the booster
- The vacuum creates a pressure difference between two chambers in the booster
- This pressure difference multiplies the force applied to the brake pedal
- The amplified force is transferred to the master cylinder, which creates hydraulic pressure
- The hydraulic pressure travels through brake lines to the wheels, causing the brakes to engage
In an electric booster, the electric motor is activated directly when the pedal is pressed, creating hydraulic pressure without needing engine vacuum.
When a brake booster is not working correctly, the driver must use much more force to press the brake pedal. The table below shows common faults, their causes, and remedies:
| Fault | Possible Causes | Remedies |
|---|---|---|
| Leakage in vacuum hoses | Heat exposure causing rubber to wear out | Replace the vacuum hoses |
| Cracked air intake manifold | Extreme pressure, strain, or overheating | Replace the intake manifold |
| Faulty intake manifold gasket | Ageing or damage | Replace the gasket |
| Faulty brake booster diaphragm | Air leak decreasing pressure | Replace the brake booster |
Note: For safety purposes, replacing and not repairing a defective brake booster is the recommended practice.
The following steps outline how to inspect an electric brake booster:
Materials Needed
- Brake fluid and cotton rags
Tools and Equipment Required
- Vehicle with electric brake booster (or teaching model)
- Brake tool kit
- Wheel stoppers
- Service manual
- Safety gear (gloves, overall, safety boots, safety clear glass)
Procedure
- Select all necessary tools and safety equipment
- Observe safety precautions
- Disconnect the negative terminal of the battery
- Locate the brake booster in the vehicle
- Inspect the booster for any signs of physical damage, loose connections, or leakages
- Reconnect the negative terminal of the battery
- Press the brake pedal and observe the electric motor of the booster — listen for any unusual sounds
- Check the electrical supply to the booster using a multimeter and compare readings to manufacturer's specifications
- Perform a brake pedal test — the pedal should feel firm and responsive
- Reinstall all removed components
- Test the performance of the brake system
- Clean the working area and tools, and store all tools according to workshop regulations
Example: Brake Booster Diagnosis
Suppose a driver in Mwanza notices that the brake pedal feels very hard when pressed and the vehicle requires more effort to stop. A mechanic should:
- First check the vacuum hoses for cracks or disconnections
- Inspect the intake manifold for any visible cracks
- Test the brake booster operation by listening for the vacuum assist when the pedal is pressed
- If the booster is faulty, recommend replacement rather than repair for safety reasons
In Tanzania, a mechanic working at a garage in Dodoma or along the Morogoro Road would regularly service brake boosters on customer vehicles. For example, a taxi driver operating a Toyota Wish (common in Dar es Salaam) might experience hard brake pedals after years of use; the mechanic would diagnose whether the electric brake booster needs inspection or replacement, ensuring the vehicle is safe for passengers traveling on busy Tanzanian roads.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools and equipment
- Diagnose brake booster
- Rectify fault brake booster
- Repair or replace fault brake booster components
- Test brake booster
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
Serviced brake booster functions according to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Diagnose and repair or replace brake booster
Principles: The student should explain the principles involved in servicing brake booster
Theories: The student should explain:
- Construction and operation of electric brake booster and its electronic systems
- Rectifying procedures of electric brake booster and its electronic systems
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What is the primary function of a brake booster in a hydraulic brake system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado