Mada za sehemu hiiServicing drum brakeMada 4
When a vehicle uses its brakes, the brake shoes press against the inside of the drum to create friction and slow down the wheel. Over time, this constant rubbing causes the brake shoes and the drum to wear thin. As the friction material gets thinner, the gap between the shoes and the drum becomes too large. This means when you press the brake pedal, the shoes have to travel farther before they touch the drum, making the brakes feel weak and spongy. Regular brake adjustment restores the correct gap so the brakes remain strong and responsive.
A brake adjuster is a small mechanical component built into the drum brake assembly. Its job is to automatically or manually maintain the proper clearance between the brake shoes and the drum. Think of it like adjusting the strings on a musical instrument — when they become too loose, you tighten them to get the right sound. Similarly, the adjuster tightens the brake shoes closer to the drum to compensate for wear.
The adjuster works with the wheel cylinder. When the friction material wears down, the wheel cylinder piston moves further out to push the shoes against the drum. The adjuster allows just the right amount of brake fluid to fill the space, keeping the running clearance constant. This ensures the brakes still work effectively even after many kilometres of use.
The following procedure shows how to adjust drum brakes safely and correctly:
-
Prepare the workplace — Select all required tools, equipment, and safety gear such as wheel blocks, a jack, safety stands, a wheel spanner, a flat screwdriver or brake adjuster tool, and personal protective equipment including overalls, safety boots, goggles, and gloves.
-
Follow safety precautions — Park the vehicle on a flat, solid surface. Apply the parking brake and place wheel chocks around the wheels that will not be lifted.
-
Disconnect the battery — Always disconnect the negative terminal of the battery before working on brake components to prevent electrical short circuits.
-
Lift the vehicle — Loosen the wheel nuts slightly, then use the jack to raise the vehicle. Place safety stands under the vehicle's proper lift points and lower the jack so the vehicle rests securely on the stands. Remove the wheel nuts and take off the tyre.
-
Find the adjustment port — Look at the back of the brake drum assembly. You will see a small round or square plug called the adjustment port. Remove this plug to expose the star-shaped adjuster wheel.
-
Adjust the brake — Insert a flat screwdriver or the special brake adjustment tool into the adjuster. Rotate the adjuster wheel while manually turning the drum by hand. Continue adjusting until the drum can no longer spin freely — you should feel slight resistance. Then, turn the adjuster back just enough so the drum rotates smoothly again. This sets the correct clearance.
-
Reassemble the vehicle — Replace the adjustment port plug, reinstall the tyre, and hand-tighten the wheel nuts. Lower the vehicle using the jack and remove the safety stands. Fully tighten the wheel nuts to the proper torque using a wheel spanner.
-
Test the brakes — Start the engine and gently apply the brakes while the vehicle is stationary. Check that the brake pedal feels firm and responsive. If possible, test drive at low speed to confirm the brakes stop the vehicle evenly.
-
Clean up — Clean the working area, remove any debris or brake dust using cotton rags, and store all tools properly according to workshop regulations.
Imagine you are working on a daladala (public minibus) in Arusha that has travelled over 80,000 kilometres. The driver complains that the brakes feel weak and the pedal goes almost to the floor before the bus slows down. After raising the vehicle and inspecting the rear drum brakes, you notice the brake shoes are worn but still have remaining lining. Using the adjustment procedure above, you turn the adjuster until the drum grips slightly, then back off until it spins freely. After reinstalling the wheels and testing, the brake pedal becomes firm again, and the daladala stops reliably. This simple adjustment saved the owner from buying new brake shoes prematurely.
In Tanzania, many small mechanic workshops in towns like Mwanza, Dodoma, and Mbeya service matatus, lorries, and private cars. Knowing how to adjust drum brakes helps a mechanic provide affordable brake servicing without immediately replacing expensive brake shoes or drums. This skill also ensures the safety of passengers travelling on crowded daladalas and buses on busy routes such as the Dar es Salaam to Morogoro highway.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Dismantle drum brakes
- Inspect drum brake components
- Locate the brake adjuster components
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
Adjusted brake conforms to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to adjust brakes
Principles: The student should explain the principles involved in adjusting drum brakes
Theories: The student should explain:
- Benefit of adjusting brakes
- Causes of drum brake failures and their remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What happens to the brakes when the gap between brake shoes and drum becomes too large due to wear?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado