Mada za sehemu hiiServicing drum brakeMada 4
- Checking brake drum
- Relining drum braking shoes
- Adjusting brakes
- Performing facing of brake drums
Performing Facing of Brake Drums
Facing brake drums is the process of machining or refinishing the inner surface of the drum to restore its smoothness and accuracy. When brake drums are used for a long time, their working surface becomes worn, scored, or uneven due to constant contact with brake shoes. Facing removes a thin layer of metal from the drum's inner surface to create a uniform finish that is within the manufacturer's specified tolerances. This process is essential for ensuring effective braking, reducing vibration, and preventing uneven wear of brake shoes.
Brake drums develop several problems over time that require facing:
Excessive wear and scoring — Continuous friction between the brake shoes and drum causes the drum's surface to wear unevenly. Deep scratches or grooves (scoring) reduce braking efficiency and can cause noise.
Galling — This occurs when tiny particles of metal from the brake shoes embed into the drum surface, creating rough patches that affect braking performance.
Heat distortion — Repeated braking generates heat that can cause the drum to warp or become out-of-round. A warped drum causes the brake pedal to pulse and reduces stopping power.
Corrosion and pitting — Moisture and contaminants can cause rust and pitting on the drum surface, leading to uneven contact with the brake shoes.
Before performing facing, a technician must inspect the drum to decide if machining is necessary. The following steps guide this inspection:
-
Remove the wheel and brake drum from the vehicle according to the service manual procedures.
-
Visually examine the drum's inner surface for visible scratches, grooves, rust, or discoloration.
-
Measure the drum's inner diameter using a brake drum micrometer or caliper. Compare the measured value with the maximum allowable diameter specified in the service manual. If the diameter exceeds the limit, the drum must be replaced rather than faced.
-
Check for out-of-round condition by measuring the diameter at different points around the drum's interior. Variation should not exceed the manufacturer's tolerance (typically 0.05 mm to 0.13 mm).
-
Inspect the drum for cracks, especially around the mounting holes. Cracked drums must be replaced.
If the drum shows wear but is still within the allowable limits, facing can be performed to restore the surface.
Facing is performed using a brake drum lathe or a portable brake grinder. The general steps are:
-
Secure the drum — Mount the drum on the lathe or use a portable facing tool that clamps inside the drum.
-
Set the cutting depth — Adjust the machining tool to remove only the minimum material needed to achieve a smooth surface, usually not exceeding 0.5 mm to 1.0 mm.
-
Machine the surface — Start the machine and slowly bring the cutting tool into contact with the drum surface. Make uniform passes until the entire inner surface is refinished.
-
Check the finish — After machining, the surface should be smooth and free from grooves. Wipe clean and inspect visually.
-
Measure final diameter — Verify that the drum's diameter is still within acceptable limits after material removal.
-
Reinstall the drum — Refit the drum, brake shoes, and wheel assembly. Adjust the brake as needed.
When performing facing of brake drums, always observe these safety measures:
- Wear safety goggles, overalls, and safety boots to protect against metal particles and heavy components.
- Ensure the vehicle is securely supported on safety stands before working underneath it.
- Disconnect the battery negative terminal before starting any brake work.
- Use wheel blocks to prevent vehicle movement.
- Keep the work area clean and free from oil or grease that could contaminate brake components.
- Follow the service manual instructions for all procedures.
In Tanzania, many daladala (minibus) operators and truck owners rely on drum brakes for their vehicles. When brake drums become worn and cause poor braking or steering wheel vibration, a mechanic can perform facing to restore the drums instead of buying new ones. For example, a daladala owner in Dar es Salaam might pay a mechanic around TSh 30,000 to face both rear brake drums, which is much cheaper than replacing the drums entirely. This saves money while ensuring the vehicle can stop safely on Tanzanian roads, especially when carrying passengers in heavy traffic or on hilly routes like those near Morogoro.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Dismantle drum brakes
- Inspect drum brake and its components
- Service drum Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
faced drum brake conforms to the manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to perform facing of brake drums
Principles: The student should explain the principles involved in performing facing of brake drums
Theories: The student should explain:
- Importance of facing the brake drum
- Causes of drum brake failures and their remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What is the primary purpose of performing facing on brake drums?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado