Mada za sehemu hiiServicing disc brakesMada 3
- Replacing brake pads
- Repairing brake caliper
- Performing facing of disc
Disc brakes are a vital part of a vehicle's braking system that uses brake pads to clamp onto a rotating disc (called a rotor) to slow down or stop the vehicle. When you press the brake pedal, hydraulic pressure pushes the brake pads against the spinning rotor. This creates friction, which slows the rotation of the wheel and brings the vehicle to a stop. Disc brakes are popular in modern vehicles because they dissipate heat efficiently and provide consistent braking performance.
Understanding the components helps you know how the system works before replacing brake pads.
Brake Disc (Rotor)
The brake disc is a metal disc attached to the wheel hub. It rotates together with the wheel. When brakes are applied, the brake pads clamp onto the rotor to slow the vehicle.
Brake Pads
Brake pads are friction materials mounted inside the calliper. They press against the brake disc to create the friction needed to stop the vehicle. Brake pads wear out over time and must be replaced regularly.
Brake Calliper
The calliper is a housing that contains the brake pads and hydraulic pistons. When you press the brake pedal, the calliper squeezes the pads against the rotor. In modern vehicles, callipers may also contain brake wear sensors to monitor pad thickness.
Pistons
Pistons are located inside the calliper. They push the brake pads against the rotor when hydraulic pressure is applied. Some vehicles have single-piston callipers, while others have multi-piston designs for stronger braking.
Brake pads are made from different materials, each with its own advantages and disadvantages.
| Material | Characteristics |
|---|---|
| Asbestos | Heat-resistant and durable; used in older vehicles and clutch systems |
| Semi-metallic | Contains metal fibers (copper or steel); good heat dissipation but can be noisy |
| Ceramic | Made from ceramic fibers; quiet operation, low dust, consistent performance, but more expensive |
Follow these steps carefully to replace brake pads safely and correctly.
Step 1: Prepare Tools, Equipment, and Safety Gear
Gather all required tools before starting:
- Wheel spanner, jack, and wheel blocks
- Service manual for the vehicle
- Brake tool kit
- Safety stands, overall, safety boots, gloves, and safety glasses
- Brake fluid and cotton rags
Step 2: Observe Safety Precautions
- Park the vehicle on a level surface and engage the parking brake
- Wear protective gear at all times
- Disconnect the negative terminal of the battery if working near electrical components
- Place wheel blocks on the wheels that remain on the ground
Step 3: Loosen Wheel Nuts and Jack Up the Vehicle
Use the wheel spanner to loosen the wheel nuts slightly while the wheel is still on the ground. Then, use the jack to lift the vehicle and place it on safety stands. Never work under a vehicle supported only by a jack.
Step 4: Remove the Tyre
Unscrew the wheel nuts completely and remove the tyre-wheel assembly to expose the brake disc and calliper.
Step 5: Lift the Calliper
Remove the slider bolts (or guide pins) that hold the calliper in place. Carefully lift the calliper away from the rotor without straining the brake hose.
Step 6: Remove the Old Brake Pads
Take out the worn brake pads from the calliper. Note their orientation so you can install the new pads correctly.
Step 7: Inspect Related Components
Before installing new pads, visually inspect:
- Calliper condition (check for leaks or corrosion)
- Brake fluid lines (ensure no cracks or leaks)
- Rotor surface (check for grooves, warping, or excessive wear)
- Piston condition (ensure it moves freely)
If any components are damaged, address them before proceeding.
Step 8: Install New Brake Pads
Insert the new brake pads into the calliper in the same position as the old ones. Ensure they sit properly and make even contact with the rotor.
Step 9: Reinstall All Removed Components
Place the calliper back onto its mounting bracket and secure it with the slider bolts. Tighten to the manufacturer's specifications. Refit the tyre and hand-tighten the wheel nuts.
Step 10: Lower the Vehicle and Bleed the Brakes
Lower the vehicle carefully using the jack. Tighten the wheel nuts properly with the wheel spanner. If the calliper was opened, you may need to bleed the brake system to remove air bubbles.
Step 11: Test Brake Performance
Start the engine and gently press the brake pedal several times to ensure the pads seat properly. Test the vehicle at low speed to confirm the brakes work correctly before driving normally.
Step 12: Clean and Store Tools
Clean the working area, wipe down tools, and store them properly according to workshop regulations. Dispose of old brake pads and rags safely.
Brake pads must be replaced when the friction lining wears down to a dangerous level. Worn pads reduce braking efficiency, increase stopping distance, and can damage the rotor. In Tanzania, mechanic shops in Dar es Salaam, Arusha, and Mwanza commonly perform this service. A typical brake pad replacement at a local garage might cost between TZS 30,000 and TZS 80,000, depending on the vehicle type and pad quality.
In Tanzania, many small vehicle owners rely on local mechanics in towns like Dodoma or Mbeya to service their vehicles. Understanding how to replace brake pads allows a mechanic to offer this common service, earning income while ensuring vehicle safety for customers who travel on busy roads between cities. For example, a taxi driver in Mwanza needs reliable brakes to safely transport passengers on mountain roads, and a properly replaced brake pad ensures the vehicle stops effectively during emergency situations.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Inspect the brake pads
- Check brake pad wear indicator and disc
- Test brakes
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
Serviced disc brakes conform to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to replace brake pads
Principles: The student should explain the principles involved in replacing brake pads
Theories: The student should explain:
- Components of disc brakes
- Advantages of disc brakes as compared to drum brakes
- Materials used for brake pads
- Embedded electronic system working together with brake pads
- Causes of disc brake failures and their remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
Which material used for brake pad linings is known for quiet operation, low dust production, and consistent performance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado