Mada za sehemu hiiServicing disc brakesMada 3
- Replacing brake pads
- Repairing brake caliper
- Performing facing of disc
A brake caliper is a key component of a disc brake system that squeezes brake pads against the rotating disc to slow down or stop a vehicle. When the brake pedal is pressed, hydraulic pressure pushes pistons inside the caliper, forcing the pads against the rotor and creating friction. Repairing a faulty brake caliper involves diagnosing common problems, disassembling the unit, and restoring its proper function.
The brake caliper consists of three main components that work together to apply braking force:
Pistons – These are hydraulic components that push the brake pads against the disc when brake fluid pressure is applied. Pistons can be single or multi-piston designs.
Brake Pads – These friction materials are held by the caliper and pressed evenly against the disc to create the necessary friction for stopping the vehicle.
Caliper Housing – This is the main body that encases the pistons and brake pads. It is often made from aluminium or cast iron for strength and durability.
Brake calipers can develop faults that reduce braking efficiency. The table below summarizes common problems, their causes, and remedies.
| S/N | Fault/Symptoms | Causes/Problems | Remedies |
|---|---|---|---|
| 1. | Caliper sticking | Corrosion, dirt accumulation, or damaged piston seal | Inspect and clean the caliper; replace if corroded |
| 2. | Caliper leaks | Damaged seals, cracked housing, or deteriorated brake lines | Replace faulty caliper or seals; bleed the brake system |
| 3. | Uneven brake pad wear | Faulty piston or slide pin, misalignment | Install brake shims between pads and caliper |
| 4. | Corrosion and rust | Exposure to moisture and road salt | Clean and treat; replace if severe |
| 5. | Caliper piston seizing | Corrosion, brake fluid contamination | Clean, lubricate, and ensure free movement; replace piston if needed |
The following procedure should be followed under teacher supervision:
-
Select tools and safety gear – Gather wheel spanner, jack, wheel blocks, service pit or hoist, safety stands, overall, safety boots, gloves, safety glasses, tool kit, and service manual.
-
Observe safety precautions – Park the vehicle on a level surface, apply parking brake, and use wheel blocks.
-
Loosen wheel nuts – Slightly loosen the nuts while the vehicle is on the ground.
-
Jack up the vehicle – Use a proper jack and support the vehicle on safety stands. Never work under a vehicle supported only by a jack.
-
Remove the wheel – Take off the tyre to access the brake assembly.
-
Remove the caliper – Take out the slider bolts and lift the caliper from the mounting bracket. Support the caliper so it does not hang on the brake hose.
-
Inspect components – Check the caliper housing, pistons, brake pads, rotor, and fluid lines for damage, wear, or leaks.
-
Repair or replace – Clean and lubricate corroded parts, replace damaged seals or pistons, and install new brake pads if worn.
-
Reassemble – Reinstall the caliper, slider bolts, and wheel.
-
Bleed the brake system – Use bleeding equipment to remove air from the brake lines.
-
Test the vehicle – Lower the vehicle and test brake performance before driving.
-
Clean and store – Clean the working area and tools, and store them according to workshop regulations.
A driver notices that the vehicle pulls to one side when braking and the brake pedal feels spongy. Upon inspection, the mechanic finds that the left brake caliper is difficult to move by hand. The cause is corrosion around the caliper piston. The remedy is to remove the caliper, clean the corrosion, lubricate the piston, and replace the seal. If the corrosion is severe, the caliper must be replaced entirely to ensure safe braking performance.
In Tanzania, brake caliper repair is a common service offered in vehicle repair garages along major roads like the Dar es Salaam to Morogoro highway. A mechanic at a small workshop in Mwanza might diagnose a sticking caliper on a taxi (daladala) by checking for uneven pad wear, cleaning the corroded slider pins, and applying fresh grease — restoring proper braking so the vehicle can safely transport passengers on busy routes.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Inspect the disc brake caliper
- Check brake disc brake caliper
- Bleed brakes
- Test brakes
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
The repaired brake caliper conforms to manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to repair brake caliper
Principles: The student should explain the principles involved in repairing brake caliper
Theories: The student should explain:
- Advantages of disc brakes as compared to drum brakes
- Causes of disc brake calipers failures and their remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
Which of the following is NOT a main component of a brake caliper?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado