Mada za sehemu hiiServicing conventional ignition systemsMada 3
- Diagnosing conventional ignition system
- Rectifying conventional ignition system
- Servicing magneto ignition system
Rectifying Conventional Ignition System
After diagnosing a conventional ignition system and identifying the faulty components, the next step is to rectify or repair those faults. Rectifying means restoring the system to proper working condition by cleaning, adjusting, repairing, or replacing damaged parts. This process ensures the engine can start easily, run smoothly, and produce the required power.
The conventional ignition system can develop several faults that affect engine performance. Understanding these faults, their causes, and how to fix them is essential for any auto-electrician.
Faults and Remedies Table
| S/N | Faults | Causes | Remedies |
|---|---|---|---|
| 1 | No spark from the spark plug | Faulty ignition coil, worn-out spark plugs, broken ignition wires, damaged distributor cap/rotor | Replace the ignition coil, install new spark plugs, check and replace ignition wires, replace distributor cap and rotor |
| 2 | Engine misfiring | Dirty or worn-out spark plugs, incorrect ignition timing, weak ignition coil | Clean or replace spark plugs, adjust ignition timing, replace faulty ignition coil |
| 3 | Weak spark output | Low-voltage supply to ignition coil, dirty or faulty breaker points, poor ground connection | Check battery voltage and charging system, clean or replace breaker points, ensure good ground connection |
| 4 | Hard starting or no start | Weak battery, defective ignition switch, loose or corroded wiring connections, worn-out distributor points | Check and charge or replace battery, repair or replace ignition switch, tighten and clean wiring connections, replace worn distributor points |
The ignition coil is one of the most critical components in the conventional ignition system. When it fails, the engine will not start or will run poorly. Below is a step-by-step procedure for rectifying a faulty ignition coil.
Required Tools and Materials
- Multimeter
- Screwdrivers
- Spanner/wrench set
- Replacement ignition coil
- Insulation tape
- Cotton rags
- Safety gloves and goggles
- Vehicle service manual
Step-by-Step Procedure
-
Prepare the vehicle: Park on a flat surface, apply handbrake, and open the hood. Disconnect the negative battery terminal for safety.
-
Locate the ignition coil: Identify the ignition coil, usually mounted near the distributor. Refer to the service manual for exact location.
-
Inspect the ignition coil: Check for visible damage such as cracks, burns, or loose connections. Look for signs of overheating or oil leakage.
-
Test primary resistance:
- Set the multimeter to ohms (Ω) setting
- Disconnect the ignition coil from the circuit
- Place multimeter probes on the primary terminals (+ and −)
- Compare the reading with manufacturer specifications (typically 0.5–2.0 Ω)
-
Test secondary resistance:
- Place one probe on the high-voltage (HT) terminal
- Place the other probe on a primary terminal
- Compare the reading with specifications (typically 6,000–10,000 Ω)
-
Replace if necessary: If either resistance is outside the specified range:
- Disconnect all electrical connectors and ignition wires
- Remove mounting bolts using a wrench
- Carefully remove the old coil
- Install the new coil and secure with bolts
- Reconnect all wires and connectors
-
Test the system: Reconnect the battery, start the engine, and check for smooth operation without misfiring or stalling.
-
Clean and store: Clean tools and the working area, then store equipment properly according to workshop regulations.
- Always compare multimeter readings with the manufacturer's specifications in the service manual
- Never work on the ignition system with the battery connected
- Use proper safety gear (gloves and goggles) when working with ignition components
- Ensure all connections are tight and secure after replacement
- Proper grounding is essential for the ignition system to work correctly
In Tanzania, a mechanic at a local garage in Dar es Salaam or Mwanza uses these rectification skills daily. For example, when a taxi driver (like a Toyota Probox driver) comes with an engine that won't start, the mechanic will diagnose the ignition system, find a weak ignition coil, replace it with a new one costing around TSh 80,000–150,000, and get the vehicle running again—earning a service fee while solving the customer's problem.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear
- Interpret circuit diagram of conventional ignition system
- Diagnose ignition system faults
- Repair faulty conventional ignition system components
- Replace defective conventional ignition system components
- Clear ignition system faults
- Test conventional ignition system
- Observe safety
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Rectified conventional ignition system functions as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain:
- How to rectify faults of conventional ignition systems
Principles: The student should explain the principles involved in rectifying conventional ignition system
Theories: The student should explain:
- Procedures for rectifying conventional ignition system
- Faults in convention ignition systems, causes and remedies
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual
Swali
Which of the following is a common cause of weak spark output in a conventional ignition system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado