Mada za sehemu hiiServicing conventional ignition systemsMada 3
- Diagnosing conventional ignition system
- Rectifying conventional ignition system
- Servicing magneto ignition system
Diagnosing Conventional Ignition Systems
A conventional ignition system is the oldest type of spark ignition system used in petrol engines. Diagnosing this system means finding faults by checking, inspecting, and testing different parts to identify which component is not working properly.
A conventional spark ignition system consists of several key components that work together to produce a strong spark for igniting the fuel.
Battery
The battery is the primary power source of the conventional ignition system. It supplies electrical energy to run the system and helps to start the engine. In most vehicles, the battery is 12 Volts.
Ignition Switch
The ignition switch is a special switch used to start and stop the engine. When turned on, it allows electric current to flow from the battery to the ignition system. It can be operated by a key or a push button and usually has positions such as OFF, ON, and START.
Ignition Coil
The ignition coil is a transformer that increases the battery voltage to a very high voltage required to create a spark at the spark plugs. It has two sets of wire windings called the primary winding and the secondary winding, with an iron core inside.
Distributor
The ignition distributor is a mechanical device that sends the high-voltage current from the ignition coil to the spark plugs. It has a distributor cap that protects internal parts. The input shaft of the distributor is driven by the engine's camshaft.
Contact Breaker
A contact breaker is a mechanical device designed to open and close the primary circuit current. It opens and closes based on ignition timing. This component is found inside the distributor and is driven by the distributor shaft.
Spark Plug
The spark plug creates the spark to ignite the air-fuel mixture inside the engine. It has a ceramic insulator, a centre electrode, and a metal shell with a grounded electrode. Spark plugs must handle high voltage, pressure, and temperature.
A conventional ignition system is mainly a mechanical system that does not use electronic control. Here is the step-by-step operation:
- The battery supplies electricity when the ignition switch is turned on.
- This electricity goes to the ignition coil through the breaker points.
- As the engine runs, the breaker points open and close with the help of a cam inside the distributor.
- When the points close, electricity flows and builds a magnetic field in the coil.
- When the points open, the magnetic field breaks suddenly and creates high voltage.
- This high voltage goes from the coil to the distributor.
- Inside the distributor, a rotating rotor sends the voltage to the correct spark plug wire.
- The electricity travels through a high-tension wire to the spark plug.
- At the spark plug, the voltage jumps across a small gap and makes a spark.
- This spark burns the air and fuel mixture in the engine.
Follow these steps to diagnose a conventional ignition system:
Step 1: Prepare and Observe Safety
- Select all required tools: multimeter, spark plug tester, ignition timing light, screwdrivers, wrenches, and service manual
- Wear safety gear: gloves, safety goggles, overcoat, safety boots
- Park the vehicle on a flat surface
Step 2: Locate and Visually Inspect Components
- Locate the components of the conventional ignition system
- Check for damaged, loose, or disconnected ignition system components such as spark plugs, ignition coil, distributor cap, and ignition wires
- Inspect the ignition coil for cracks or signs of overheating
Step 3: Inspect Spark Plugs
- Remove the spark plug and inspect its condition
- Look for carbon deposits, oil fouling, or burning
- Check the electrode gap
Step 4: Test the Ignition Coil
- Set the multimeter to the ohms (Ω) setting
- Measure the primary resistance by placing the multimeter probes on the coil's primary terminals
- Measure the secondary coil resistance by placing one probe on the high-voltage output terminal and the other on a primary terminal
- Compare readings with manufacturer specifications in the service manual
Step 5: Inspect the Distributor
- Remove the distributor cap and check for moisture, dirt, or corrosion
- Inspect the rotor for wear or damage
- Check breaker points for proper gap and condition
Step 6: Check Electrical Supply
- Use a multimeter to check the voltage supply to the ignition coil and distributor
- Ensure there are no wiring faults, shorts, or loose connections
Step 7: Record Findings and Clean Up
- Record all defective components
- Clean tools and equipment
- Store tools as per workshop regulations
| Faults | Causes | Remedies |
|---|---|---|
| No spark from the spark plug | Faulty ignition coil, worn-out spark plugs, broken ignition wires, damaged distributor cap/rotor | Replace ignition coil, install new spark plugs, replace ignition wires, replace distributor cap and rotor |
| Engine misfiring | Dirty or worn-out spark plugs, incorrect ignition timing, weak ignition coil | Clean or replace spark plugs, adjust ignition timing, replace faulty ignition coil |
| Weak spark output | Low-voltage supply to ignition coil, dirty or faulty breaker points, poor ground connection | Check battery voltage and charging system, clean or replace breaker points, ensure good ground connection |
| Hard starting or no start | Weak battery, defective ignition switch, loose or corroded wiring connections, worn-out distributor points | Check and charge or replace battery, repair or replace ignition switch, tighten and clean wiring connections, replace worn-out distributor points |
A student is diagnosing a vehicle that will not start. Using a multimeter, they measure the primary resistance of the ignition coil as 3.2 Ω. The vehicle service manual specifies primary resistance should be between 0.5 Ω and 1.5 Ω.
Analysis: The measured primary resistance of 3.2 Ω is much higher than the maximum specification of 1.5 Ω. This means the ignition coil is defective and must be replaced.
Action: Replace the ignition coil with a new one that meets the manufacturer's specifications. After replacement, test the engine to ensure it starts properly.
In Tanzania, a mechanic at a local garage in Dar es Salaam or Mwanza uses these diagnostic skills daily. For example, when a taxi driver brings a vehicle that won't start, the mechanic applies the same procedures—checking spark plugs, testing the ignition coil with a multimeter, and inspecting the distributor—to identify the problem and get the taxi back on the road, earning income for the business.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear
- Interpret circuit diagram of conventional ignition system
- Identify and locate conventional ignition system components
- Inspect the conventional ignition system components
- Read the fault codes of conventional ignition system
- Test conventional ignition system components
- Observe safety
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Diagnosed conventional ignition system faults are isolated as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain:
- How to diagnose of conventional ignition systems
- Diagnostic procedures of conventional ignition systems
Principles: The student should explain the principles involved in diagnosing conventional ignition system
Theories: The student should explain:
- Types of ignition systems
- Describe the construction and operation of ignition system
- Function of conventional ignition system
- components of the conventional ignition systems
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual
Swali
What is the primary function of the ignition coil in a conventional ignition system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado