Mada za sehemu hiiServicing wiper and washer systemsMada 2
- Diagnosing the wiper and washer system
- Rectifying wiper and washer system
Rectification is the process of fixing identified faults in the wiper and washer system by repairing or replacing defective components to restore their normal operation.
After you have diagnosed the wiper and washer system and identified which parts are faulty, rectification follows. This step involves correcting the problems so the system can work properly again. Rectification may include cleaning clogged parts, tightening loose connections, repairing damaged wiring, or replacing components that are severely damaged.
The table below summarizes the typical faults you may encounter in wiper and washer systems, their causes, and how to fix each one.
| S/No | Faults | Causes | Remedies |
|---|---|---|---|
| 1 | Wipers do not move | Faulty motor, blown fuse, bad connection | Replace the fuse; replace the motor; inspect and fix wiring connections |
| 2 | Skipping wipers | Worn-out wiper blades | Replace the wiper blades |
| 3 | Washer fluid not spraying | Clogged nozzles, low fluid level, faulty pump | Clean the nozzles; refill washer fluid; inspect and replace the pump |
| 4 | Wipers move unexpectedly | Loose linkages, faulty motor, electrical faults | Tighten linkages; check and replace motor; check wiring |
Follow these systematic steps to rectify faults in the wiper and washer system:
-
Select tools and safety gear — Put on your PPE (overcoat, safety boots, safety gloves, safety glasses) and gather screwdrivers, pliers, multimeter, test light, and replacement parts.
-
Observe safety precautions — Disconnect the battery negative terminal before working on electrical components.
-
Replace blown fuses — Use a multimeter to check fuse continuity. If blown, replace with a new fuse of the correct rating as specified in the vehicle service manual.
-
Replace wiper blades — Remove worn, torn, or ineffective blades and install new ones of the correct size.
-
Replace faulty switch or relay — Test the combination switch and relay using a multimeter. Replace if they fail to operate properly.
-
Replace wiper motor — If the motor fails to operate or does not return to the park position, remove it and install a new motor matching manufacturer specifications.
-
Clean or replace clogged nozzles — Use a fine pin, wire, or small brush to remove debris from washer nozzles. Replace if cleaning does not restore spray.
-
Repair washer hoses — Replace any damaged, disconnected, or leaking washer fluid hoses to restore proper fluid flow.
-
Refill washer fluid — Fill the reservoir with appropriate cleaning solution up to the required level.
-
Reconnect components — Ensure all electrical and mechanical connections are secure, tight, and free from corrosion.
-
Test the system — Reconnect the battery and test the wiper and washer system to confirm proper operation at all speeds.
-
Clean the work area — Reinstall any removed panels and store tools according to workshop regulations.
A driver reports that the wipers on a Toyota Hilux do not move at all. After diagnosis, you find the wiper motor is faulty and the fuse is blown.
Rectification steps:
- First, you check the fuse with a multimeter and find no continuity, confirming it is blown.
- You replace the 15-amp fuse with a new one of the correct rating.
- Then you test the wiper motor by applying battery voltage directly. It does not move, confirming the motor is faulty.
- You remove the defective motor and install a new wiper motor according to the service manual specifications.
- After reconnecting all wiring and testing, the wipers now operate at both low and high speeds.
In Tanzania, taxi and daladala drivers rely on functioning wiper systems during the rainy season, especially on busy routes like those in Dar es Salaam where sudden downpours are common. If a driver's wipers stop working, they can now diagnose and repair the fault themselves using basic tools, saving the cost of visiting a garage and ensuring safe driving for passengers.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Interpret circuit diagrams of wiper and washer systems
- Inspect the wiper and washer system
- Repair faulty components of the wiper and washer system
- Replace defective components of wiper and washer system
- Service the wiper and washer system circuit
- Test system
- Observe safety
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Rectified wiper and washer system works as per manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain:
- How to rectify wiper and washer systems
Principles: The student should explain the principles involved in rectifying wiper and washer systems
Theories: The student should explain:
- Procedures for rectifying wiper and washer system components
- Possible faults, causes and remedies of wiper and washer system
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual
Swali
What is the first step in the rectification procedure for wiper and washer systems?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado