Mada za sehemu hiiReplacing tyresMada 3
- Replacing worn tyre
- Refilling pressure and foam material in tyre
- Performing tyre rotation
Replacing a Worn Tyre
A worn tyre is a tyre that has become too thin or damaged through use and cannot safely support the vehicle. Replacing a worn tyre is an essential maintenance skill that every auto mechanic must know. A worn tyre can cause poor vehicle handling, reduced braking efficiency, and even accidents. This note will guide you through the complete procedure of safely replacing a worn tyre using the correct tools and safety measures.
Before starting any tyre replacement work, always observe the following safety rules:
- Wear safety boots to protect your feet from heavy wheels and tools
- Wear gloves to protect your hands from dirt and sharp edges
- Wear safety clear glasses to protect your eyes from dust and debris
- Wear overalls to protect your clothing
- Use a mask when working with dusty or dirty tyres
- Always apply the parking brake before starting work
- Use wheel chocks or stoppers on the wheels that remain on the ground
- Never work under a vehicle that is only supported by a jack — always use jack stands
The following tools and equipment are required for replacing a worn tyre:
- Vehicle with worn tyre
- Wheel chocks or stoppers
- Jack
- Wheel spanner
- Tyre lever
- Pliers
- Air compressor
- Tyre pressure gauge
- Safety gear: gloves, safety boots, overall, safety clear glasses, mask
Follow these steps carefully to replace a worn tyre safely and correctly:
Step 1: Prepare the Vehicle
- Park the vehicle on a firm, level surface away from traffic
- Apply the parking brake to secure the vehicle
- Place wheel chocks or stoppers on both sides of the wheels that will remain on the ground (opposite the wheel you are replacing)
Step 2: Loosen the Wheel Nuts
- Using the wheel spanner, loosen the wheel nuts on the worn tyre
- Turn each nut approximately one-quarter turn counter-clockwise
- Do not remove the nuts completely at this stage — only loosen them while the wheel is still on the ground
Step 3: Jack Up the Vehicle
- Position the jack under the vehicle's designated jacking point (refer to the vehicle manual)
- Pump the jack handle to raise the vehicle until the worn wheel is clearly off the ground
- Ensure the vehicle is stable and the jack is properly positioned before proceeding
Step 4: Remove the Worn Wheel
- Completely unscrew all the wheel nuts using the wheel spanner
- Remove the nuts and keep them in a safe place
- Carefully pull the worn wheel away from the wheel hub
- Place the worn wheel flat on the ground to prevent it from rolling away
Step 5: Mount the Replacement Wheel
- Clean the wheel hub surface if necessary
- Position the replacement wheel onto the wheel hub, aligning the bolt holes
- Hand-tighten the wheel nuts onto the bolts
- Ensure the wheel is seated properly on the hub before proceeding
Step 6: Lower the Vehicle
- Slowly lower the vehicle using the jack until the replacement wheel touches the ground
- Remove the jack
- Use the wheel spanner to fully tighten the wheel nuts in a diagonal pattern (tighten one nut, then the opposite one, and so on)
- This diagonal pattern ensures even tightening and prevents the wheel from becoming lopsided
Step 7: Check Tyre Pressure
- Use the air compressor and tyre pressure gauge to check the pressure in the new tyre
- Compare the reading with the manufacturer's recommended pressure (usually found on a sticker inside the driver's door frame)
- If the pressure is too low, add air using the compressor
- If the pressure is too high, release air by pressing the valve stem
Step 8: Final Inspection
- Verify that all wheel nuts are properly tightened
- Ensure the vehicle is stable on all wheels
- Remove the wheel chocks or stoppers
- Store all tools and equipment properly
Imagine you are working on a daladala (public minibus) that needs its front left tyre replaced. The tyre is worn and the driver has a spare wheel ready. Following the procedure above:
- You park the daladala at the bus stand, apply the parking brake, and place wheel chocks on the rear wheels
- You loosen the five wheel nuts on the front left tyre
- You position the jack under the front left jacking point and raise the vehicle
- You remove all five nuts and take off the worn wheel
- You mount the spare wheel and hand-tighten the nuts
- You lower the vehicle and tighten the nuts in a diagonal pattern
- You check the tyre pressure — it reads 28 PSI, but the recommended is 32 PSI, so you add air
- You do a final check and the daladala is ready to continue its route
- Forgetting to apply the parking brake before starting work
- Not using wheel chocks or stoppers on the opposite wheels
- Tightening wheel nuts in the wrong order (always use diagonal pattern)
- Over-tightening or under-tightening wheel nuts
- Not checking tyre pressure after mounting the new tyre
- Working under a vehicle that is only supported by a jack (always use jack stands for safety)
In Tanzania, taxi and daladala drivers frequently need to replace worn tyres at roadside tyre repair shops in cities like Dar es Salaam, Arusha, and Mwanza. Knowing how to replace a worn tyre yourself can save time and money — for example, a roadside tyre replacement service might charge TSh 10,000 to TSh 15,000, but if you can do it yourself using your own jack and tools, you only spend money on the new tyre and air. This skill is also valuable for truck and lorry drivers who travel long distances on Tanzania's highways where tyre wear is high.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Park vehicle safely
- Secure the vehicle
- Loosen the lug nuts
- Lift the vehicle
- Remove the worn tire
- Mount the new tire
- Secure the lug nuts
- Lower the vehicle
- Observe safety precautions
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Replaced worn tyre conforms to technical specifications and standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to replace tyres
Principles: The student should explain the principles involved in replacing tyres
Theories: The student should explain:
- Meaning of tyres
- Construction of tyres
- Functions of tyres
- Types of tyres
- Interpretation of tyre dimensions and specifications
- Properties of tyres
- Importance of replacing worn tyre
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacturer’s services manual book
Swali
What is the first step to take before beginning tyre replacement work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado