Mada za sehemu hiiServicing engine lubrication systemsMada 2
- Changing engine oil
- Changing engine oil filter
An oil filter is a component mounted on the outside of the engine lubrication system. Its job is to remove dirt, metal particles, and other impurities from the engine oil. Without a working oil filter, contaminated oil would circulate through the engine, causing increased wear on moving parts like the crankshaft, camshaft, and piston rings. This can lead to reduced engine performance, higher fuel consumption, and eventually serious engine damage. Replacing the oil filter during every oil change keeps the engine lubricating system clean and efficient.
There are two main types of oil filters used in vehicle lubrication systems:
Full-Flow Oil Filters
Full-flow filters, also called inline filters, are used in most modern engines. All engine oil passes through this filter before it enters the engine. The filter removes larger particles of contaminants that could harm the engine. This ensures that clean oil lubricates all engine components.
Bypass Oil Filters
Bypass filters are found mainly in older vehicles. These filters only filter a portion of the oil pumped by the oil pump. The remaining oil goes directly to the oil gallery. Bypass filters use very efficient filtering media designed to remove the smallest contaminant particles. The oil that passes through a bypass filter typically returns to the sump.
Follow these steps carefully under your teacher's supervision:
-
Select tools and materials — Gather the oil filter, cotton rags, oil filter wrench, draining pan, jack, safety stand, wheel chocks, vehicle service manual, and lubricating oil.
-
Observe safety precautions — Wear gloves, overalls, and safety boots. Ensure the workshop is well-ventilated.
-
Prepare the vehicle — Insert wheel chocks on all wheels. Open the vehicle bonnet.
-
Ensure engine is cool — Wait until the engine has cooled down to avoid burns from hot oil.
-
Disconnect the battery — Disconnect the negative terminal of the battery to prevent electrical accidents.
-
Inspect for leakages — Check the engine for any oil leaks around the filter and sump.
-
Clean the work area — Wipe the engine and oil filter with cotton rags to remove dirt and oil.
-
Identify the correct filter — Refer to the service manual to confirm the correct oil filter type and part number for the vehicle.
-
Position the draining pan — Place the oil-draining pan beneath the oil filter to catch any oil that drips during removal.
-
Remove the old filter — Use an oil filter wrench to loosen the oil filter. Turn it counterclockwise until it can be removed by hand. Be careful — some oil will still be inside the filter.
-
Inspect the old filter and mounting — Check the condition of the old filter and inspect the filter mounting thread for damage or debris.
-
Prepare the new filter — Lubricate the rubber gasket (positioning gasket) of the new oil filter with a small amount of clean engine oil. This helps create a proper seal and makes removal easier during the next change.
-
Pre-fill the filter — Fill the new oil filter with clean engine oil before installing it. This reduces the time the engine runs with low oil pressure at startup.
-
Install the new filter — Screw the new oil filter onto the mounting boss by hand. Turn it clockwise until the gasket contacts the mounting surface, then tighten an additional three-quarter turn. Do not over-tighten.
-
Remove the draining pan — Carefully take the draining pan out from underneath the vehicle.
-
Check and refill engine oil — Inspect the engine oil level using the dipstick. If needed, add oil to reach the required level between the low and full marks.
-
Reconnect the battery — Connect the negative battery terminal.
-
Run the engine — Start the engine and let it run for about 30 seconds to a minute, then switch it off. This allows oil to circulate and the filter to fill completely.
-
Reinspect the oil level — After the engine has been off for a minute, check the oil level again using the dipstick. Add more oil if necessary to reach the proper level.
-
Complete the job — Close the bonnet, remove the safety stand and wheel chocks. Clean all tools and store them according to workshop regulations.
- Always change the oil filter whenever you change the engine oil.
- Ensure the engine is cool before starting work to prevent burns.
- Never over-tighten the oil filter — this can damage the gasket and cause leaks.
- Lubricate the new filter's gasket with oil before installation for a proper seal.
- Use the correct filter type as specified in the vehicle service manual.
- Always dispose of the old oil and filter properly at designated collection points.
In Tanzania, commercial drivers and mechanics in Arusha, Mwanza, and Dodoma regularly change oil filters during routine vehicle servicing to prevent engine breakdowns on long-distance routes like the Dar es Salaam to Mbeya highway. A taxi driver in Dar es Salaam who changes the oil filter every 5,000 km can extend the engine life of a Toyota Probox by up to three years, saving up to TZS 1,500,000 in potential major repairs. This maintenance skill is also valuable for small vehicle rental businesses and transport cooperatives that need to keep their fleets running efficiently.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Keep vehicle on level ground/hoist/service pit
- Locate oil filter
- Remove fuel filter
- Fit new filter
- Inspect the engine to check oil leakage
- Observe safety precautions
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
The serviced engine lubrication system’s filter is replaced according to the manufacturer’s specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Remove and refi the new filter
- Check for leakage
Principles: The student should explain the principles involved in changing oil filter
Theories: The student should explain:
- Types of oil filters
- Importance of oil filter
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What is the primary function of an oil filter in a vehicle engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado