Mada za sehemu hiiServicing engine lubrication systemsMada 2
- Changing engine oil
- Changing engine oil filter
Changing Engine Oil
Changing engine oil is a routine maintenance task that keeps an engine running smoothly by lubricating moving parts, cooling engine components, and removing contaminants. This note explains how to identify the correct engine oil, understand lubrication methods, check oil levels, and safely change the oil in a vehicle engine.
Engine oil serves three main purposes in a vehicle:
- Lubrication – reduces friction between moving metal parts such as pistons, crankshaft, and camshaft
- Cooling – carries heat away from critical engine components
- Cleaning – removes dirt, sludge, and metal particles that result from engine wear
Viscosity
Viscosity is the measure of an oil's thickness or its ability to flow. Thin (low-viscosity) oil flows easily and reaches engine parts quickly during cold starts. Thick (high-viscosity) oil provides stronger film strength under high temperatures but flows slowly when cold.
Oil viscosity changes with temperature: as temperature increases, viscosity decreases (oil becomes thinner). This is why manufacturers specify different oil grades for different climates.
Oil Grade Identification
Engine oils are classified by the Society of Automotive Engineers (SAE) viscosity rating system:
- Cold weather (winter) grades: SAE 15W, 20W, 30W, 40W
- Hot weather (tropical) grades: SAE 15, 20, 30, 40
- Multi-weather grades: SAE 30-15W, 40-20W, 50-15W
In Tanzania's tropical climate, the recommended grades are typically SAE 40 or SAE 50 for most vehicles, though some manufacturers specify multi-weather grades like SAE 15W-40.
Oil Deterioration
Over time, engine oil breaks down due to:
- High engine temperatures
- Pressure from combustion
- Contamination by fuel, coolant, and metal particles
Manufacturers recommend oil change intervals based on either time (typically 3–6 months) or distance driven (usually 5,000–10,000 km). Using deteriorated oil increases engine wear and can cause serious damage.
Conventional Engine Oil
Derived from crude oil, conventional oils contain natural impurities and varying molecular structures. They include cleansing and anti-corrosion additives but tend to break down faster than synthetic oils, requiring more frequent changes.
Synthetic Engine Oil
Synthetic oils are chemically engineered with uniform molecular chains. They:
- Withstand higher and lower temperatures without breaking down
- Stay cleaner for longer periods
- Provide better protection under extreme conditions
These oils cost more but last longer between changes.
Synthetic Blended Engine Oil
A mixture of conventional and synthetic oils, blended oils offer a balance between cost and performance. They have better oxidation resistance and stability than conventional oils alone.
Bath or Splash Lubrication
In this method, moving engine parts such as gears or camshaft lobes dip into an oil bath. As they rotate, they splash oil onto other components. This method is simple and requires no oil pump or filter. It is commonly used in gearboxes and differentials.
Force-Feed Lubrication
Most modern vehicle engines use force-feed lubrication. An oil pump draws oil from the sump and pressurizes it through passages to the crankshaft, camshaft, and other critical components. This method ensures oil reaches all bearing surfaces efficiently, even at high engine speeds.
The oil dipstick is a simple tool used to check the engine oil level:
- Park the vehicle on level ground and wait a few minutes for oil to settle
- Remove the dipstick from the engine
- Wipe it clean with a rag
- Reinsert it fully, then pull it out again
- The oil level should fall between the LOW and FULL marks
If the level is below the LOW mark, add oil gradually until it reaches the FULL mark. Never overfill above FULL, as this can cause seal damage and increased pressure.
The following steps describe how to change engine oil safely:
Preparation
- Gather required tools and materials: drain pan, funnel, drain plug spanner, oil filter wrench, jack, safety stand, wheel chocks, correct grade engine oil, gloves, cotton rags, and vehicle service manual
- Apply wheel chocks to all wheels for safety
- Jack the vehicle and place it on a safety stand
- Open the engine bonnet
- Disconnect the positive battery terminal to prevent electrical hazards
- Inspect the engine for visible oil leaks
Draining the Old Oil
- Locate the engine sump and oil drain plug
- Position the drain pan beneath the drain plug
- Remove the oil filler cap from the valve cover
- Unscrew the drain plug using the appropriate spanner
- Allow all oil to drain completely into the pan (typically 5–10 minutes)
- Inspect the drain plug threads and the sump hole for damage or wear
- Reinstall the drain plug and tighten to the torque specification in the service manual (usually 25–35 Nm for most vehicles)
- Remove the drain pan from underneath
Adding New Oil
- Insert a clean funnel into the oil filler opening
- Pour the correct grade and quantity of oil into the engine (refer to service manual for capacity, typically 3–5 litres)
- Remove the funnel and reinstall the oil filler cap
- Run the engine for about 30 seconds to circulate the new oil
- Switch off the engine and wait 2–3 minutes for oil to settle
- Check the oil level using the dipstick and add more if necessary to reach the FULL mark
- Reconnect the battery terminal
Completion
- Clean any spilled oil from the engine and surrounding area
- Lower the vehicle safely
- Clean all tools and store them properly according to workshop regulations
Example: A common petrol engine in Tanzania, such as a Toyota Corolla, uses SAE 15W-40 multi-grade oil. The oil capacity is approximately 3.8 litres. After draining the old oil (which should be dark and thin), the mechanic adds 3.5 litres initially, checks the dipstick, and adds the remaining 0.3 litre to reach the FULL mark.
In Tanzania, taxi and daladala drivers who cover long distances on poor roads depend on regular oil changes to keep their vehicles running. A driver in Dar es Salaam who changes the oil every 5,000 km using locally available SAE 40 oil (costing around TSh 25,000–35,000 per litre) can avoid expensive engine repairs that would cost over TSh 500,000, keeping their vehicle reliable for daily passenger transport.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Use service manual
- Keep vehicle on level ground/hoist/service pit
- Identify engine oil types and uses
- Check oil level
- Test engine for oil leakage
- Observe safety precautions
- Clean tools, equipment and work place
- Store tools and equipment
Tathmini ya matokeo
The serviced engine lubrication system contains the correct type and level of engine oil according to the manufacturer’s specifications or service manual
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Check oil condition and level
- Change engine oil
- Check for leakage
Principles: The student should explain the principles involved in changing engine oil
Theories: The student should explain:
- Importance of changing engine oil
- Oil types according to engine fuel type
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacture’s service manual book
Swali
What are the three main purposes of engine oil in a vehicle engine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado