Mada za sehemu hiiCarrying out gas cutting on thick metal platesMada 3
- Performing metal selection
- Performing blow pipe pressure setting
- Performing metal cutting
Performing Blowpipe Pressure Setting
When cutting thick metal plates using oxy-fuel cutting, correct blowpipe (cutting torch) pressure settings are essential for achieving clean, precise cuts. The blowpipe uses a combination of oxygen and fuel gas (typically acetylene) to generate a high-temperature flame that heats and melts the metal. Setting the pressures correctly ensures the flame has enough heat to penetrate thick metal while maintaining cutting efficiency and safety.
Proper gas pressure settings directly affect:
- Cut quality: Correct pressures produce smooth, clean cuts without excessive slag
- Cutting speed: Proper pressure allows for steady, uniform cutting
- Safety: Incorrect pressures can cause flashbacks, backfires, or poor flame control
- Equipment longevity: Proper pressures prevent damage to the torch and nozzles
The oxygen pressure must be significantly higher than the fuel gas pressure to create a powerful oxygen jet that blows away molten metal during cutting.
Materials:
- Blowpipe (cutting torch)
- Oxygen gas cylinder
- Acetylene gas cylinder
- Scrap piece of metal (for test cutting)
- Cotton rags
Tools and Equipment:
- Personal protective equipment (PPE): overall, leather apron, industrial boots, leather gloves, welding goggles
- Gas regulators
- Gas hoses
- Spark lighter
- Wire brush
- Cutting nozzles or tips
Step 1: Prepare and Inspect Equipment
Before starting, ensure you are properly dressed in all personal protective equipment. Then inspect the blowpipe:
- Check that the cutting torch is clean and free of blockages
- Verify all connections are secure and in good working condition
- Make sure both gas cylinders are properly connected and contain sufficient gas
Step 2: Check and Set Gas Regulators
Examine the regulators on both oxygen and acetylene cylinders:
- Ensure regulators are functioning correctly
- Verify they are set appropriately for the planned cutting task
Step 3: Set Acetylene Pressure
Adjust the acetylene (fuel gas) pressure to the correct range:
- Set acetylene pressure between 0.5 to 1.5 bar for cutting operations
This range provides adequate fuel for the preheating flame without causing instability.
Step 4: Set Oxygen Pressure
Set the oxygen pressure higher than the acetylene:
- Set oxygen pressure between 2 to 3 bar for general cutting
- For thicker metals (above 12 mm), increase oxygen pressure even higher
The oxygen pressure must be significantly higher to create a strong cutting jet that oxidizes and removes the molten metal.
Step 5: Ignite and Observe the Flame
Light the blowpipe using a spark lighter:
- Hold the spark lighter near the nozzle opening
- Slowly open the acetylene valve and ignite the gas
- Adjust both oxygen and acetylene valves to achieve a neutral flame
A neutral flame has a well-defined inner cone and is preferred for most cutting operations because it provides consistent heat without adding or removing material from the cut zone.
Step 6: Perform a Test Cut
Before cutting the actual workpiece, test your settings:
- Use a scrap piece of metal for the test cut
- Observe the flame—it should remain steady without fluctuating in size or intensity
- Check the quality of the cut: it should be smooth with minimal slag
- If the flame flickers or the cut is poor, adjust pressures and retest
Step 7: Clean and Store Equipment
After completing the pressure setting and test cut:
- Turn off both oxygen and acetylene supplies properly
- Allow the equipment to cool before handling
- Clean the work area, tools, and equipment
- Store all equipment appropriately
- Acetylene pressure: 0.5–1.5 bar
- Oxygen pressure: 2–3 bar (higher for thicker metals)
- Oxygen pressure must always be higher than acetylene pressure
- Always perform a test cut before actual work
- Wear all required PPE throughout the process
- A neutral flame is generally preferred for cutting
If oxygen pressure is too low:
- The oxygen jet becomes weak and cannot effectively blow away molten metal
- The cut becomes narrow, uneven, or may not penetrate fully
- Slag builds up on the cut surface
If oxygen pressure is too high:
- The flame becomes unstable
- Excess oxygen can cause the metal to oxidize excessively
- Wasted gas increases operational costs
If acetylene pressure is too high:
- The flame becomes lazy and inconsistent
- Carbon deposits may form on the cut surface
In Tanzania, auto-body repair technicians in cities like Dar es Salaam, Arusha, and Mwanza use oxy-fuel cutting equipment to cut thick metal panels during vehicle body repairs. For example, when repairing a damaged truck body frame, a technician must correctly set the blowpipe pressures—acetylene at 1.0 bar and oxygen at 2.5 bar—to ensure clean cuts through 10 mm thick steel plates. Proper pressure setting helps avoid damaging the vehicle's structural integrity and ensures the repaired body meets safety standards for commercial vehicles operating on Tanzanian roads.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Prepare and inspect gas welding plant
- Set cutting pressure on the regulator
- Regulate the flame
- Observe safety regulations
- Clean the working area
- Clean tools and equipment
- Store tools and gas plant in safety
Tathmini ya matokeo
Blow pipe pressure set as per specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to set blow pipe pressure for cutting
Principles: The student should outline the principles used to set blow pipe pressure for cutting
Theories: The student should explain the processes of cutting thick metal by gas
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed
- First aid
Swali
What is the correct acetylene pressure range for cutting thick metal plates?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado