Mada za sehemu hiiCarrying out gas cutting on thick metal platesMada 3
- Performing metal selection
- Performing blow pipe pressure setting
- Performing metal cutting
Performing Metal Cutting
Metal cutting by gas flame is a process used to cut through metals using a combination of fuel gas and oxygen. The heat generated by the gas flame heats and melts the metal, dividing it into pieces. This process is highly effective for ferrous metals because they readily oxidise when exposed to an oxygen jet once they reach their ignition temperature.
Gas Cutting Torch
A gas cutting torch is different from a standard welding torch because it has an extra lever to regulate the flow of cutting oxygen. A welding torch can be transformed into a cutting torch by replacing the mixing head with a cutting attachment. The torch includes standard oxygen and acetylene valves to control the flow of gases during cutting.
Gas Cutting Nozzle
The cutting nozzle (also called a cutting tip) is a crucial component that regulates the flow of oxygen and fuel gas to generate the high-temperature flame needed for cutting. The nozzle has a central orifice for oxygen flow, surrounded by several smaller holes that direct a preheating flame.
Flashbacks
A flashback occurs when the flame retreats into the torch or hoses, potentially igniting gases within the equipment and causing explosions. This may result from improper flame and pressure adjustments, inadequate equipment maintenance, or incorrect pressure settings.
Backfires
A backfire occurs when the flame momentarily burns back inside the torch, creating a loud popping sound and potentially damaging the torch. This typically arises from an improper torch cutting angle and incorrect distance between the torch and the workpiece.
Prevention Measures
To prevent flashbacks and backfires, maintain correct equipment setup, properly adjust flame and gas pressures, and follow safe operating practices. Regular equipment inspections, correct flame settings, and maintaining a steady cutting speed are essential.
Thick metal plates have a thickness greater than 6 mm. When selecting thick metal plates for gas cutting, consider the following:
- Material type: Choose carbon steel or mild steel plates, which are ideal for oxy-fuel cutting because they oxidise readily.
- Thickness: Confirm the plate thickness is above 6 mm. Greater thickness allows for better control over the cut.
- Plate condition: Remove contaminants such as rust, oil, grease, paint, and mill scale. Clean surfaces facilitate better preheating and a smoother cut.
Note: Non-ferrous metals like aluminium do not oxidise in the same manner as ferrous metals and are therefore not suitable for oxy-acetylene gas cutting.
Correct blowpipe pressure settings are critical for effective cutting. The steps are:
- Ensure the cutting torch is clean, free of blockages, and in good working condition.
- Connect oxygen and fuel gas cylinders properly and securely.
- Set acetylene pressure to 0.5 to 1.5 bar for cutting.
- Set oxygen pressure higher than acetylene, typically between 2 to 3 bar or higher for thicker metals.
- Ignite the torch and adjust to a neutral flame.
- Perform a test cut on scrap metal to verify quality before proceeding.
Important: Oxygen pressure must be significantly higher than fuel gas pressure to ensure proper cutting.
Oxy-acetylene thick metal cutting is a widely used method for cutting thick steel. The process follows these steps:
Procedure
- Wear proper personal protective equipment (overalls, leather apron, industrial boots, leather gloves, tongs, welding goggles).
- Select proper tools, equipment, and materials.
- Clean the metal plate thoroughly to remove dirt, oil, rust, or paint.
- Measure and mark the area designated for cutting using chalk and measuring tools.
- Set gas pressure: Ensure oxygen pressure is significantly higher than fuel gas pressure.
- Choose a nozzle size suitable for thicker plates to ensure higher oxygen flow rates.
- Light the torch and adjust to an oxidising flame setting.
- Position the torch over the starting point and heat the metal until it reaches a glowing red to orange colour.
- Initiate oxygen flow and move the torch slowly along the cut line at a steady, consistent pace.
- Turn off both oxygen and fuel gas supply, and allow the metal to cool before inspecting the work.
- Clean and store tools, equipment, and the work area.
Key Differences: Thick vs. Thin Metal Cutting
| Aspect | Thin Metal (less than 6mm) | Thick Metal (over 6mm) |
|---|---|---|
| Preheating time | Shorter | Longer |
| Cutting speed | Faster | Slower |
| Oxygen pressure | Lower (slightly above fuel gas) | Higher (significantly above fuel gas) |
| Nozzle size | Smaller | Larger |
Example: Cutting a 10mm Mild Steel Plate
A mechanic needs to cut a 10mm thick mild steel plate to fabricate a repair panel for a truck body. The mechanic would:
- Select a 10mm carbon steel plate (suitable for oxy-fuel cutting)
- Set acetylene pressure to 1.0 bar and oxygen pressure to 3.0 bar
- Choose a larger cutting nozzle designed for thick plates
- Heat the metal for several seconds until glowing red
- Begin cutting at a slower, steady pace to ensure the oxygen jet penetrates through the full thickness
The result is a clean cut with minimal slag, as the higher oxygen pressure effectively blows away the oxidised material throughout the entire thickness of the plate.
In Tanzania, auto-body repair technicians in cities like Dar es Salaam and Arusha regularly use gas cutting to reshape damaged vehicle panels. For example, a mechanic repairing a crashed daladala (minibus) might use oxy-acetylene cutting to remove the damaged section of a rusty body panel and prepare the area for welding a new piece of sheet metal. This skill is essential for cost-effective vehicle repairs in local workshops where plasma cutting equipment may be too expensive.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Prepare and inspect gas welding plant
- Interpret working drawing
- Regulate the flame
- Perform the metal cutting
- Shut off gas regulators
- Chip of slag’s
- Inspect the correctness
- Observe safety regulation
- Clean the working area
- Clean tools and equipment
- Store tools and gas plant in a safe place
Tathmini ya matokeo
Gas cut workpiece conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to cut thick metals using gas
Principles: The student should state the principles of gas cutting on thick metals
Theories: The student should explain the processes of cutting thick metal by gas
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed
- First aid
Swali
According to the textbook, what is the minimum thickness that classifies a metal plate as "thick" for gas cutting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado