Mada za sehemu hiiCarrying out welding on plates using MIG and TIG weldingMada 3
- Performing MIG welding
- Performing TIG welding on copper plates
- Performing TIG welding on aluminium plates
TIG welding (Tungsten Inert Gas) is a precision welding process that uses a non-consumable tungsten electrode and inert gas to protect the weld area. In auto-body repair, TIG welding is used to join copper plates for radiator repairs, fuel tanks, and other non-ferrous body parts because copper has excellent heat and electrical conductivity.
- Wear welding shield (dark glass #10 or #12) to protect eyes from intense light
- Wear leather gloves and protective clothing to prevent burns
- Ensure proper ventilation in the work area to remove fumes
- Keep fire extinguisher nearby
- Disconnect power before changing electrodes
- Ensure workpieces are clamped securely before welding
- TIG welding machine with argon gas supply
- Welding cables and earth clamp
- Tungsten electrode (usually 2% lanthanated or thoriated)
- Filler rod (copper or silicon bronze)
- Welding shield with appropriate shade
- Chipping hammer and wire brush
- Angle grinder with grinding disc
- Tongs for handling hot materials
- Bench vice and clamps
- Scriber for marking
- Clean the copper plate - Remove all dirt, oil, grease, and oxide layer using acetone or degreaser
- Mill or grind the edges - Prepare butt joints by beveling edges to allow proper penetration
- Fit up the joint - Align plates in bench vice or with clamps, ensuring minimal gap (0-1mm for thin plates)
- Mark the weld zone - Use scriber to mark start and finish points
- Set up earth clamp - Connect earth clamp close to the weld area on clean copper
Step 1: Set Up the TIG Machine
- Select DCEN (Direct Current Electrode Negative) polarity
- Set appropriate amperage (typically 80-150A for 3mm copper plate)
- Connect argon gas bottle and set flow rate to 15-20 CFH
- Install appropriate tungsten electrode (2.4mm diameter for general work)
- Grind tungsten to pointed tip angle of 20-30 degrees
Step 2: Strike the Arc
- Hold torch at 70-80 degree angle to workpiece
- Use high-frequency start or scratch start technique
- Establish a small molten pool on the copper surface
- Maintain consistent arc length of 2-3mm
Step 3: Form the Weld Pool
- Allow the argon gas to shield the molten pool completely
- Move torch in a circular or figure-eight motion to create even heating
- The weld pool on copper will appear bright orange-yellow when properly heated
- Add filler rod by dipping into the leading edge of the pool
Step 4: Progress the Weld
- Advance slowly along the joint at consistent speed
- Maintain the same angle and arc length throughout
- Add filler rod rhythmically - dip, melt, and withdraw
- Keep the weld pool visible and controlled
Step 5: Complete and Finish
- Run off the edge of the workpiece at the end of weld
- Allow workpiece to cool gradually under argon shielding
- Remove slag and discoloration with chipping hammer and wire brush
- Inspect weld for defects
| Fault | Possible Cause | Remedy |
|---|---|---|
| Porosity | Contaminated surface, insufficient gas | Clean thoroughly, increase gas flow |
| Lack of penetration | Low amperage, too fast travel | Increase amperage, slow down |
| Excessive spatter | Arc length too long, wrong technique | Maintain proper arc length |
| Cracking | Rapid cooling, high stress | Preheat copper, use proper filler |
After welding, examine the joint for:
- Uniform bead appearance without gaps
- No cracks or porosity on surface
- Proper penetration at the root
- Clean appearance after brushing
In Tanzania, TIG welding skills on copper plates are essential for automotive radiator repair shops in cities like Dar es Salaam, Arusha, and Mwanza. When a taxi or daladala radiator develops a leak, a skilled technician can TIG weld the copper radiator tank to restore it at lower cost than replacing the entire unit — a repair that might cost around TSh 30,000-50,000 compared to TSh 150,000+ for a new radiator. This skill also supports small welding fabrication workshops that repair copper water heaters and electrical components in local communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select tools, equipment and safety gears
- Inspect TIG and MIG welding equipment and accessories
- Select the correct filler metal
- Align and tack weld the workpiece
- Maintain work and lead angle
- Maintain uniform travel speed along the joint
- Control distortion
- Clean tools and equipment and store them safely
Tathmini ya matokeo
Welded copper workpiece conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain different welding techniques
Principles: The student should explain the principles of:
- TIG welding
- Purging
Theories: The student should:
- Distinguish different types of tungsten electrodes
- Distinguish different TIG welding techniques
- Identify types of materials for TIG welding
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed
- Workshop rules and regulation
- First Aid
Swali
Which safety equipment is required when performing TIG welding on copper plates?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado