Mada za sehemu hiiCarrying out welding on plates using MIG and TIG weldingMada 3
- Performing MIG welding
- Performing TIG welding on copper plates
- Performing TIG welding on aluminium plates
TIG Welding on Aluminium Plates
TIG (Tungsten Inert Gas) welding is a precision welding process that uses a non-consumable tungsten electrode to produce the weld. It is commonly used in auto-body repair for aluminium body panels because it produces clean, strong welds with minimal distortion. In this learning activity, you will practice TIG welding on aluminium plates, which is an essential skill for repairing vehicle body parts.
TIG welding, also known as Gas Tungsten Arc Welding (GTAW), uses an inert gas (usually argon) to protect the weld area from atmospheric contamination. The process offers several advantages for aluminium body work:
- High precision: Produces fine, accurate welds suitable for visible body panels
- Low heat input: Minimizes warping of thin aluminium sheets
- Clean appearance: Produces smooth weld beads with minimal spatter
- Good penetration: Strong welds on aluminium of various thicknesses
Aluminium behaves differently from steel during welding, and understanding these differences is crucial:
-
Oxide layer: Aluminium instantly forms a thin oxide layer (Al₂O₃) on its surface that melts at a much higher temperature (approximately 2,050°C) than the base metal (660°C). This oxide layer must be removed before welding using a stainless steel wire brush dedicated only to aluminium.
-
High thermal conductivity: Aluminium conducts heat quickly, requiring higher heat input and faster travel speed compared to steel.
-
Low melting point: Aluminium melts at around 660°C, much lower than steel (1,500°C), so careful heat control is needed to avoid burning through.
-
No color change: Unlike steel, aluminium does not change color as it approaches melting point, making it difficult to judge proper welding temperature by eye.
Before starting any welding work, always observe these safety measures:
- Wear dark welding shield (shade 10-12 for TIG) to protect eyes from intense UV light
- Wear leather welding gloves and apron to protect from sparks and heat
- Ensure proper ventilation to remove fumes and gases
- Keep flammable materials away from the work area
- Inspect cables and connections for damage before use
- Ensure the work bench is stable and secure
- Use tongs to handle hot materials
- Connect earth clamp properly to prevent electrical shock
| Equipment/Material | Purpose |
|---|---|
| TIG welding machine | Provides the electrical energy for welding |
| Welding cables | Transmit electrical current |
| Earth clamp | Completes electrical circuit by connecting to workpiece |
| Argon gas cylinder + regulator | Provides inert shielding gas |
| Tungsten electrode | Non-consumable electrode that creates the arc |
| Filler rod (aluminium) | Adds material to make the weld |
| Welding shield | Protects eyes and face |
| Chipping hammer | Removes slag from weld |
| Stainless steel wire brush | Cleans aluminium oxide (dedicated to aluminium only) |
| Angle grinder | Prepares edges and removes material |
| Work bench | Supports workpiece during welding |
| Bench vice | Holds materials securely |
| Tongs | Handles hot materials safely |
| Scriber | Marks layout lines on metal |
Proper preparation is essential for a successful aluminium TIG weld:
Step 1: Clean the aluminium plate
Use the stainless steel wire brush specifically for aluminium to remove the oxide layer. Brush in one direction only, not back and forth. Clean an area slightly larger than the weld zone. If the plate is greasy, first clean with acetone or appropriate aluminium cleaner.
Step 2: Fit the workpieces
If joining two plates, fit them together properly:
- Ensure proper alignment using the scriber to mark layout lines
- Clamp the plates in the bench vice or use clamps
- Leave a small gap (approximately 1-2mm) for penetration
- For butt joints, grind the edges to create a proper edge preparation
Step 3: Set up the TIG machine
- Connect the welding cable to the torch
- Connect the earth clamp to the work bench or directly to the aluminium plate
- Set the polarity to DCEN (Direct Current Electrode Negative)
- Select appropriate amperage for the aluminium thickness (approximately 1 amp per 1mm of thickness as a starting point)
- Set argon gas flow rate to 15-20 CFH (cubic feet per hour)
Step 1: Strike the arc
Hold the TIG torch at a 70-80° angle to the workpiece. Touch the tungsten electrode to the metal and quickly lift it to create the arc, or use the high-frequency start if available. Maintain a short arc length (approximately 2-3mm).
Step 2: Create the weld pool
Allow the arc to heat the aluminium until a small molten pool forms. The pool will appear shiny and fluid. If the pool is too fluid and spreads too much, increase travel speed. If the pool is too small and does not flow, increase amperage slightly.
Step 3: Add filler metal
Once the weld pool is established, begin adding the filler rod:
- Hold the filler rod at a 15-20° angle to the workpiece
- Dip the tip of the filler rod into the leading edge of the weld pool
- Withdraw the filler rod as the wire melts into the pool
- Maintain a consistent rhythm: dip, melt, withdraw, move forward
Step 4: Travel along the joint
Move the torch steadily along the joint line while maintaining:
- Consistent arc length (2-3mm)
- Consistent travel speed
- Steady filler rod addition
- Angle of torch pointing toward the direction of travel
Step 5: Complete the weld
When reaching the end of the joint, gradually reduce heat by pulling back on the torch or using the amperage control. Allow the weld pool to solidify before moving the torch away. Let the workpiece cool naturally—do not quench with water.
A mechanic needs to repair a cracked aluminium panel on a pickup truck. The crack runs 100mm along a 3mm thick aluminium plate. The following parameters should be used:
- Material thickness: 3mm aluminium plate
- Weld type: Butt joint (single V not required for thin material)
- Amperage setting: Start with 3mm × 1 amp/mm = 30 amps, adjust as needed
- Tungsten electrode: 2.4mm diameter, lanthanated or thoriated (green or red tip)
- Filler rod: 3mm diameter aluminium alloy (4043 or 5356)
- Shielding gas: 100% argon, 18 CFH flow rate
- Travel speed: Steady speed to produce a weld bead approximately 6mm wide
Procedure:
- Clean the crack area with the stainless steel wire brush
- Clamp the plate securely on the work bench
- Set TIG machine to 30 amps DCEN
- Open argon valve and set flow to 18 CFH
- Strike arc and establish weld pool at one end of crack
- Add filler rod while moving torch along the crack
- Complete the weld and allow to cool
- Inspect weld for uniformity and penetration
After completing the weld:
Step 1: Allow cooling
Let the welded plate cool naturally. Forced cooling may cause cracking in aluminium.
Step 2: Clean the weld
Use the chipping hammer to remove any oxide residue. Then use the aluminium-dedicated wire brush to clean the weld bead and surrounding area.
Step 3: Inspect the weld
Examine the weld for:
- Uniform bead width and height
- No cracks or porosity (holes)
- Proper penetration (wetting at the edges)
- No burns or excessive spatter
- Consistent appearance along the entire length
Step 4: Finish if required
Use the angle grinder with a flap disc or sanding disc to smooth the weld if a flush surface is needed for body work.
| Defect | Possible Cause |
|---|---|
| Porosity (holes) | Contaminated metal, insufficient gas coverage, improper filler rod |
| Lack of fusion | Insufficient heat, travel speed too fast, improper joint preparation |
| Burn through | Too much heat, gap too wide, travel speed too slow |
| Cracking | Rapid cooling, wrong filler alloy, high residual stress |
| Poor bead appearance | Inconsistent travel speed, improper filler rod technique |
In Tanzania, TIG welding of aluminium plates is a valuable skill for auto-body repair technicians working in Dar es Salaam, Arusha, Mwanza, and other cities where pickup trucks, SUVs, and modern vehicles with aluminium body panels are common. For example, a mechanic at a bodyshop in Mwanza might use TIG welding to repair a damaged aluminium cargo bed on a Toyota Hilux, producing a strong, rust-resistant weld that restores the vehicle's structural integrity. This skill enables technicians to offer quality repair services for both local and imported vehicles, supporting small businesses and providing employment opportunities in the growing automotive repair sector.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Inspect TIG and MIG welding equipment and accessories
- Select the correct filler metal
- Align and tack weld the workpiece
- Maintain work and lead angle
- Maintain uniform travel speed along the joint
- Control distortion
- Clean tools and equipment and store them safely
Tathmini ya matokeo
Welded aluminium workpiece conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain different welding techniques
Principles: The student should outline the principles of:
- TIG welding
- Purging
Theories: The student should:
- Distinguish different types of tungsten electrodes
- Elaborate different TIG welding techniques
- Identify types of materials for TIG welding
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed
- Workshop rules and regulation First Aid
Swali
What is the main reason why aluminium must be cleaned with a dedicated stainless steel wire brush before TIG welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado