Mada za sehemu hiiCarrying out gas welding on ferrous and non-ferrous metalsMada 3
- Performing gas welding
- Performing gas welding on non-ferrous metals
- Performing gas welding of copper and its alloys
Gas welding is a process that uses a flame produced by burning fuel gases (commonly oxy-acetylene) to melt and join metals. Copper and its alloys—such as brass and bronze—are non-ferrous metals commonly found in vehicle radiators, fuel lines, and electrical components. Because copper conducts heat very well and has a high melting point, welding it requires special techniques compared to steel.
Before welding copper, you must understand its key properties:
- High thermal conductivity – copper spreads heat quickly, requiring a hotter flame and preheating
- High melting point – pure copper melts at about 1083°C
- Oxidation – copper forms a black oxide layer (cupric oxide) on its surface when heated
- Alloys behave differently – brass (copper + zinc) and bronze (copper + tin) have different melting points and require adjusted techniques
Gather the following before starting:
- Oxy-acetylene plant with pressure regulator
- Welding torch with correct tip size for copper
- Hose pipes connected to the regulator
- Gas trolley for safe cylinder placement
- Cylinder key for opening valves
- Blow pipe spanner for tightening connections
- Spark lighter for igniting the flame
- Hammer and chisel for cleaning joints
- Wire brush for removing oxides
- Clean copper or copper alloy pieces for practice
Step 1: Clean the material
Use a wire brush, chisel, and hammer to remove dirt, grease, and oxide layers from the area to be welded. Clean surfaces ensure proper fusion.
Step 2: Fit and secure the workpieces
Position the copper pieces in the correct alignment. Clamp or hold them firmly to prevent movement during welding.
Step 3: Set up the oxy-acetylene equipment
Connect hoses properly (red for acetylene, green or blue for oxygen). Use the cylinder key to open the cylinder valves slowly. Set working pressures as recommended—typically 5–10 kPa for acetylene and 15–20 kPa for oxygen for copper welding.
Step 4: Light and adjust the flame
Use a spark lighter to ignite the torch. Start with a neutral flame (balanced oxygen and acetylene), then adjust to a slightly carbureting (excess acetylene) flame for copper, which helps reduce oxide formation.
Step 1: Preheat the joint
Because copper conducts heat quickly, direct the flame at the joint area to preheat it uniformly. Move the flame in a circular motion until the copper glows dull red.
Step 2: Add filler rod
Introduce a copper or copper-alloy filler rod into the flame near the joint. Allow the base metal and filler to melt together.
Step 3: Form the weld pool
Maintain a steady flame angle (about 45° to the work surface). Create a small weld pool and progressively move along the joint.
Step 4: Complete the weld
Continue adding filler metal while moving the torch steadily until the joint is fully fused. Allow the weld to cool slowly to avoid cracking.
- Always wear welding gloves, goggles, and protective clothing
- Work in a well-ventilated area to avoid inhaling fumes
- Keep a fire extinguisher nearby
- Never oil or grease oxygen or acetylene equipment
- Ensure cylinders are secured upright on the gas trolley
- Allow welded parts to cool before handling
- Porosity – caused by dirty materials or incorrect flame; always clean surfaces and use proper flame
- Cracking – occurs from rapid cooling; let the work cool slowly
- Incomplete fusion – from insufficient heat; ensure proper preheating
In Tanzania, auto mechanics in Dar es Salaam, Arusha, and Mwanza regularly repair vehicle radiators and copper fuel lines using gas welding. For example, when a taxi driver's radiator develops a leak, a skilled technician can use oxy-acetylene welding to join a new copper section, saving the cost of buying a completely new radiator—which can cost over TZS 500,000. This skill also helps small workshops in rural areas serve local farmers whose irrigation pumps use copper components.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Inspect gas welding equipment
- Assemble and disassemble gas cylinders
- Select nozzle sizes
- Select welding filler wires
- Set working pressure
- Align and tack weld the workpiece
- Check root penetration
- Inspect quality of weld ripples
- Clean work place, tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
Welded copper and its alloys by gas conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain the gas welding technique used
Principles: The student should explain the principles of:
- Welding by gas flame
- Low pressure blow pipe
- High pressure blow pipe
Theories: The student should :
- Describe the main parts of oxyacetylene plant and their functions
- Elaborate different gas welding techniques
- Distinguish different types of flames
- Describe storage of gas cylinders
- State the metallurgy of metals (basic)
- Describe heat and temperature related to welding
Circumstantial knowledge:
Detailed knowledge about:
- OSHA rules and regulations
- Workshop rules and regulations
- Safe working practices
- Waste disposal procedures
Swali
Which fuel gases are most commonly used for gas welding copper and its alloys?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado