Mada za sehemu hiiCarrying out gas cutting on ferrous metalsMada 2
- Cutting steel plate by automatic machine flame
- Cutting steel plate by stack cutting
Automatic machine flame cutting is a method of cutting steel plates using an oxy-acetylene torch that is moved automatically by a machine, rather than by hand. The machine follows a pre-set pattern or guide to make straight, accurate cuts on ferrous metals like steel. This method is faster and more precise than hand-held cutting, making it ideal for production work in vehicle body repair shops.
Before starting, gather the following equipment:
- Oxy-acetylene plant – provides the oxygen and fuel gases
- Pressure regulator – controls gas pressure
- Cutting torch – the tool that produces the flame
- Automatic cutting machine – the device that moves the torch along a set path
- Welding torch – for preheating if needed
- Hose pipes – to connect gas cylinders to the torch
- Gas trolley – for moving cylinders safely
- Cylinder key – to open gas valves
- Blow pipe spanner – for tightening connections
- Spark lighter – to ignite the flame
- Tongs – for handling hot metal
- Hammer and chisel – for removing slag
- Wire brush – for cleaning the cut surface
- Safety gear – welding gloves, goggles, apron, steel-toed boots
- Wear appropriate protective clothing including gloves, goggles, and apron
- Check all connections for leaks using soap solution
- Ensure the work area is free from flammable materials
- Keep fire extinguisher nearby
- Never leave the torch unattended while lit
- Allow the metal to cool before handling
- Ensure proper ventilation in the working area
Step 1: Preparation
- Secure the steel plate on the cutting table or work surface
- Clean the plate surface with a wire brush to remove rust, paint, or dirt
- Mark the cutting line clearly using a scribe or marker
Step 2: Setting Up the Machine
- Install the cutting torch in the machine carriage
- Adjust the torch height according to the plate thickness
- Set the cutting speed on the machine controller
- Connect the oxygen and fuel gas hoses to the cutting torch
Step 3: Igniting the Flame
- Open the acetylene valve slightly and ignite with a spark lighter
- Adjust to get a neutral flame
- Open the oxygen valve to establish the cutting flame
- Allow the metal to preheat at the start point until it reaches glowing temperature
Step 4: Starting the Cut
- Begin the automatic cutting cycle
- The machine moves the torch along the marked line
- The high-pressure oxygen jet oxidizes and blows away the molten metal
- Maintain consistent speed for a clean, straight cut
Step 5: Completing the Cut
- Continue along the entire cutting path
- Watch for any deviations from the marked line
- Allow the cut edge to cool naturally
- Remove slag and rough edges using a hammer and chisel
- Clean the cut surface with a wire brush
A vehicle body shop needs to cut a steel bracket measuring 300 mm × 150 mm from a 6 mm thick steel plate.
Procedure:
- Clean the plate surface and mark the rectangle (300 mm × 150 mm) using a scribe
- Set up the automatic cutting machine with a 6 mm thick plate profile
- Adjust oxygen pressure to 4–5 bar and acetylene to 0.5–1 bar
- Set cutting speed to approximately 400 mm/min for 6 mm steel
- Start the machine from one corner of the marked rectangle
- The machine follows each side of the rectangle automatically
- After cutting, remove slag and brush the edges clean
The result is a precisely cut bracket with smooth edges ready for fitting.
After cutting, examine the work for:
- Straightness – the cut should follow the marked line accurately
- Smoothness – the edge should be relatively smooth without excessive roughness
- Dross – minimal slag or dross buildup on the cut surface
- Heat-affected zone – minimal distortion around the cut area
In Tanzanian vehicle repair shops and panel beating workshops in cities like Dar es Salaam, Arusha, and Mwanza, automatic flame cutting machines are used to cut replacement steel panels from flat sheets when repairing accident-damaged vehicles. For example, when replacing a rusted door panel, a technician uses an automatic cutting machine to cut the new steel sheet to exact dimensions, saving time compared to manual cutting and ensuring a proper fit for the vehicle body.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select tools, equipment and safety gears
- Inspect gas welding equipment
- Assemble and disassemble gas cylinders
- Select nozzle sizes
- Select welding filler wires
- Set working pressure
- Align and tack weld the workpiece
- Check root penetration
- Inspect the quality of weld ripples
- Clean workplace, tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
A workpiece cut by automatic machine flame conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain gas weld cutting procedures
Principles: The student should explain the principles of:
- Operating automatic flame cutting machine
- Cutting metal by flame
- Smooth cutting
- Flame setting for cutting
Theories: The student should:
- Describe parts of automatic flame cutting machine
- Describe their functions
- Suggest recommended work flames and pressure
- Elaborate different cutting procedures
Circumstantial knowledge:
Detailed knowledge about:
- OSHA rules and regulations
- Workshop rules and regulations
- Safe working practices
- Waste disposal procedures
Swali
What is the main advantage of automatic machine flame cutting compared to hand-held cutting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado