Mada za sehemu hiiCarrying out gas cutting on ferrous metalsMada 2
- Cutting steel plate by automatic machine flame
- Cutting steel plate by stack cutting
Cutting Steel Plate by Stack Cutting
Stack cutting (also called multiple-plate cutting) is a technique where two or more steel plates are clamped together and cut simultaneously using an oxy-acetylene cutting torch. This method allows a student to produce several identical parts from a single cutting operation, saving both time and cutting gas.
When repairing vehicle bodies, auto-body technicians often need several brackets, reinforcement plates, or patches of the same size and shape. Stack cutting provides:
- Consistency – All plates in the stack receive the same cut dimensions
- Time efficiency – One setup produces multiple pieces
- Cost savings – Reduced gas consumption and torch wear
- Improved accuracy – Once the pattern is set, human error is reduced across all pieces
Before cutting, proper preparation is essential:
- Select matching plates – Use plates of the same thickness, type, and surface condition
- Clean the plates – Remove rust, paint, oil, and debris using a wire brush
- Align the plates – Stack them carefully, ensuring edges are perfectly aligned
- Clamp the stack – Use clamps or a mechanical holder to hold plates firmly together. The stack should not exceed the capacity of the cutting torch
- Mark the cutting line – Use a scribe or soapstone on the top plate to indicate where the cut will be made
Follow these step-by-step guidelines:
Step 1: Set Up the Equipment
- Position the oxy-acetylene plant on a gas trolley
- Connect the hose pipes securely to the regulators and torch
- Open the cylinder valves slowly and set working pressures: typically 2–4 bar for oxygen and 0.5–1.5 bar for acetylene
Step 2: Light the Cutting Torch
- Use a spark lighter to ignite the acetylene
- Adjust to a neutral flame
- Turn on the oxygen lever to obtain a sharp inner cone
Step 3: Start the Cut
- Begin at the edge of the marked line
- Hold the torch at a 90-degree angle to the plate surface
- Pre-heat the starting point until the metal turns bright orange (about 2–3 seconds)
- Fully open the oxygen lever to begin the cut
Step 4: Maintain the Cut
- Move the torch slowly and steadily along the marked line
- Keep the torch perpendicular to ensure a straight kerf (the slot created by cutting)
- Ensure the oxygen stream completely pierces through all plates in the stack
Step 5: Complete and Cool
- Reach the end of the line and close the oxygen lever to stop cutting
- Allow the plates to cool naturally before removing clamps
- Separate the cut pieces and clean any slag or burrs with a chisel and hammer
- Wear approved safety goggles, leather gloves, and flame-resistant clothing
- Ensure the workshop is well-ventilated
- Keep a fire extinguisher and sand bucket nearby
- Never leave the lit torch unattended
- Use tongs when handling hot plates
- Check all hose connections for leaks before starting
After cutting, examine each plate:
- Verify that all pieces match the required dimensions
- Check that the cut edges are smooth and free from excessive slag
- Ensure no distortion or warping has occurred
- Confirm that the kerf width is consistent throughout
If cuts are uneven, review torch speed, angle, and gas pressure before retrying.
In Tanzania, small auto-body workshops in cities like Dar es Salaam and Arusha often receive orders for multiple identical bracket replacements from insurance companies or fleet owners. Using stack cutting, a technician can cut four or five reinforcement plates from a single stack in less time than it would take to cut them individually. This saves on oxy-acetylene gas costs—where a small cylinder of acetylene costs around TSh 30,000 to TSh 45,000—and allows the shop to complete vehicle repairs more affordably for customers.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Inspect gas welding equipment
- Assemble and disassemble gas cylinders
- Select nozzle sizes
- Select welding filler wires
- Set working pressure
- Align and tack weld the workpiece
- Check root penetration
- Inspect quality of weld ripples
- Clean work place, tools and equipment
- Store tools and equipment safely
Tathmini ya matokeo
A stack of steel plate cut conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain gas weld cutting procedures
Principles: The student should explain the principles of:
- Operating automatic flame cutting machine
- Cutting metal by flame
- Smooth cutting
- Flame setting for cutting
Theories: The student should:
- Describe parts of automatic flame cutting machine
- Describe their functions
- Suggest recommended work flames and pressure
- Explain different cutting procedures
Circumstantial knowledge:
Detailed knowledge about:
- OSHA rules and regulations
- Workshop rules and regulations
- Safe working practices
- Waste disposal procedures
Swali
What is stack cutting in auto-body repair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado