Mada za sehemu hiiCarrying out installation of a wind screen and vent glassMada 3
- Checking pole for straightness
- Checking wind screen frame for correct alignment and fitting a wind screen into the frame
- Fitting glass window machine and window glass
A window machine, also called a window regulator or winder, is the mechanism inside a vehicle door that raises and lowers the window glass. Fitting it correctly, together with the door glass and the small vent glasses, keeps water, dust and wind noise out of the vehicle and lets the windows work smoothly and safely.
- Toughened (tempered) glass is used for most door, vent and rear windows. It is heat-treated to make it several times stronger than ordinary glass. When it breaks, it shatters into small blunt pieces. It cannot be cut, drilled or ground after it is made, so the correct glass for the vehicle model must be used.
- Laminated glass is used for windscreens. Two sheets of glass are bonded to a plastic layer between them, so the glass cracks but stays in one piece.
All glass is hard but brittle. It does not bend, it breaks easily if it is knocked on the edge or twisted, and it is scratched by grit.
- Manual window machine – worked by turning a winder handle on the door.
- Electric window machine – worked by a small electric motor and a switch.
Both are made in two main designs:
- Scissor (arm) type – a toothed gear moves crossed steel arms that push the glass up and let it down.
- Cable type – a cable running over pulleys pulls a glass carrier up and down a rail.
The glass sits in a lifting channel or clamps on the machine and slides in rubber-lined guide channels in the door frame.
| Rubber part | Function |
|---|---|
| Glass run channel (felt-lined rubber) | Guides the sliding glass, stops rattles and seals the sides and top |
| Waist seals, inner and outer | Wipe the glass and keep water and dust out of the door |
| Weatherstrip (rubber gasket) | Holds a fixed or vent glass in its opening and seals it to the body |
| Locking strip | Pressed into some gaskets to tighten them on the glass |
Rubber that is hard, cracked or shrunk must be replaced.
- Measuring tape and scriber – for measuring and marking
- Glass holding tools (suction holders) – for carrying and positioning glass
- Screwdrivers and a set of pliers – for trim, clips and fixing bolts
- Soft hammer – for seating rubber, never for striking glass
- Rubber cutter – for cutting rubber to length
- Strong, smooth rope and soapy water – for fitting glass into rubber
- Step ladder or stand – for reaching windows on tall vehicles
- Toolbox – for carrying and storing the tools
- Clear goggles, leather gloves, hand gloves, overalls, leather apron and industrial boots
- Park on level ground and put on safety gear. For electric windows, disconnect the battery.
- Remove the winder handle, armrest and door trim panel, and peel back the plastic water sheet carefully so that it can be reused.
- Remove any broken glass from inside the door and check that the drain holes are clear.
- Pass the window machine through the opening in the door, line it up with its mounting holes and fit the bolts loosely. Connect the motor plug on an electric machine.
- Lower the glass into the door at an angle, seat its edges in the guide channels and fix it to the lifting channel or clamps. Tighten gently: too much force cracks the glass.
- Refit the handle (or reconnect the battery) and wind the glass fully up and down. Move the machine or guide channel in its slotted holes until the glass runs smoothly, sits square and closes fully into the top channel, then tighten all the bolts.
- Put a little grease on the gear and sliding parts of the machine, keeping it off the glass and rubber.
- Refit the water sheet and the trim panel.
Keep fingers clear of the arms when the glass is moving, and never operate an electric window with a hand inside the door.
- Clean the metal edge (flange) of the opening and treat any rust.
- Fit the rubber: press the rubber gasket onto the edge of the glass all the way round, with the join at the bottom centre.
- Fix the rope: press the rope into the outer groove of the rubber, the groove that will grip the body flange. Start and finish at the bottom centre, and let the two ends cross over and hang free by about 20 cm.
- Wet the rubber and the flange with soapy water.
- Use others to assist: a helper outside holds the glass in the centre of the opening and presses on it with flat hands, while you work inside. The rope ends must hang inside the vehicle.
- Pull one end of the rope slowly towards the centre of the glass. The rope lifts the lip of the rubber over the flange. Work along the bottom, up each side and across the top while the helper keeps pressing just ahead of the rope.
- Tap the rubber, not the glass, with the palm or a soft hammer to seat it, and press in the locking strip if there is one.
- The rubber lip must sit over the flange all the way round, with an even gap between glass and body.
- Door glass must wind fully up and down without sticking, tilting or rattling.
- Have a helper pour water over the outside, starting at the bottom, while you watch inside for drips. Where water enters, reseat the rubber or apply glass sealer under the lip, then test again.
A vent glass measures about 400 mm by 300 mm. Rubber and rope must be cut for it.
- Distance round the glass = 2×(400+300)=1,400 mm
- Rubber: add 20 mm so that the joint closes tightly: 1,400+20=1,420 mm
- Rope: add 200 mm at each end for the overlap and for gripping: 1,400+400=1,800 mm
- Wear goggles and gloves whenever glass is handled, and carry large glass upright with two people.
- Stand glass on its edge on wood or thick cloth, never on a bare concrete floor.
- Never force glass into place; if it does not fit, find out why.
- Sweep up broken glass at once and put it in a strong, labelled container for safe disposal, where it cannot harm people, animals or tyres. Do not burn old rubber or dump it on open ground.
- Wipe the tools clean, wash soap and grease off the glass holders, and store everything in the toolbox in a dry, secure place.
Daladala minibuses and pickups working on rough roads around Mbeya or Morogoro often suffer broken door glass and worn window machines. A fitter who can replace a window machine, set the glass so that it closes fully, and fit a vent glass that does not leak in the rainy season gives the customer a secure, dry vehicle and wins repeat business for the workshop.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gears
- Fit rubber to the vent glasses
- Fix the rope
- Use others to assist
- Check for correctness
- Fix vent glasses
- Check for leakage
- Observe safety regulations rules
- Clean tools and store them safely
Tathmini ya matokeo
The vent glasses installed conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain the screen and vent glass fixing techniques
Principles: The student should explain the principles of:
- Operating window glass
- Fixing window
- Installing window glass machines material
- Tools used in installation
Theories: The student should:
- Describe glass properties
- Distinguish types of window machine
- Enumerate rubber sealing materials and functions
- List down fixing tools
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while fixing the screen and vent glass
- Environment issues
Swali
What type of glass is typically used for vehicle windscreens?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado