Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Counterboring drilled holes
A bench drilling machine is a stationary tool used to create accurate holes in metal, wood, or plastic. It is mounted securely on a workbench and provides precise control over hole depth, position, and size, making it essential for workshop tasks.
A bench drilling machine, also called a bench drill press, is a stationary machine fixed to a workbench. It uses a rotating drill bit to create clean, precise holes in various materials. The machine has adjustable parts that let you control the drilling depth and the angle of the hole.
The bench drill machine has several important parts:
- Fixed Position: The machine is securely mounted on a workbench or stand, making it stable during operation.
- Drill Head: Contains the motor and spindle that holds the drill bit. It moves up and down to control drilling depth.
- Work Table: A flat surface that can be adjusted up or down and tilted to different angles for various drilling positions.
- Chuck: A three-jaw or four-jaw device that holds the drill bit firmly in place.
- Depth Stop: Allows you to set exactly how deep the drill bit will go, ensuring all holes are the same depth.
- Speed Control: Some machines let you adjust the rotation speed, which is important for different materials and hole sizes.
| Tools/Equipment | Materials | Safety Gears |
|---|---|---|
| Work bench | Coolant | Safety boots |
| Bench vice | Cotton waste | Overall |
| Drill bits (various sizes) | Workpiece (metal, wood, or plastic) | Leather gloves |
| Centre punch | Oil | Safety goggles |
| Scriber | ||
| Steel rule | ||
| Try square | ||
| Vernier caliper | ||
| Wire brush |
Always follow these safety rules when using the bench drilling machine:
- Examine the machine before use to ensure it is in good working order.
- Check the power cable and plug for damage. Do not use a damaged machine.
- Keep the power cable away from the working area.
- Secure the workpiece firmly to the work table using a vice or clamps.
- Use the correct size chuck key and attach it to the lead with tape.
- Hold the machine at right angles (90°) to the workpiece.
- Use wooden strips under the workpiece to protect the workbench.
- Place the machine where it cannot be knocked down and where no one can trip over the power lead.
- Wear appropriate PPE at all times.
Step 1: Select the Drill Bit
Choose the correct drill bit for your material and the required hole size. Secure the bit tightly in the chuck using the chuck key.
Step 2: Secure the Workpiece
Clamp the workpiece firmly to the work table. Make sure it is properly aligned with where you need to drill the hole.
Step 3: Set the Drilling Depth
Adjust the depth stop or use the drill head's depth adjustment to set how deep the hole should be. This ensures all holes have the same depth.
Step 4: Position the Workpiece
Place the workpiece directly below the drill bit. Align it carefully with the marked drilling location.
Step 5: Adjust the Work Table
Set the work table to the correct height and angle if needed for the hole orientation.
Step 6: Power On
Switch on the bench drilling machine using the power control.
Step 7: Start Drilling
Slowly lower the drill head by turning the feed handle. The drill bit will penetrate the workpiece and create the hole. Keep a firm grip on the feed handle for control.
Step 8: Monitor Drilling
Watch the drilling process to ensure the machine runs smoothly and the workpiece stays in place. Apply coolant if needed to keep the bit cool.
Step 9: Lift the Drill Head
After completing the hole, raise the drill head by turning the feed handle back.
Step 10: Remove the Workpiece
Carefully remove the workpiece from the work table.
Step 11: Power Off
Turn off the bench drilling machine when finished.
Suppose you need to drill three holes of 3mm, 6mm, and 9mm diameter in a flat bar measuring 100mm × 100mm × 10mm:
- Mark the positions for the three holes using a centre punch and scriber.
- Select a 3mm drill bit and secure it in the chuck.
- Clamp the flat bar firmly to the work table.
- Set the depth stop to 10mm (the thickness of the material).
- Drill the first hole, then repeat with 6mm and 9mm drill bits.
- Check each hole with a vernier caliper to confirm the diameter.
In Tanzania, a mechanic at a local motorcycle repair shop in Arusha or Dar es Salaam would use a bench drilling machine to create holes when fabricating custom brackets or repairing agricultural equipment like water pumps and irrigation system parts. For example, when attaching a new fuel tank bracket to a motorcycle, the mechanic would drill precise holes using a bench drill to ensure the bracket fits securely, preventing leaks or mechanical failure.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings.
- Select tools, equipment and materials
- Mark work piece.
- Drill holes
- Observe safety precautions
- Clean tools, equipment, work piece and work place
- Store tools, equipment
Tathmini ya matokeo
Drilling on bench drilling machine carried out as per provided worksheet
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Carry out drilling on bench drilling machine
Principles: The the principles of: Carrying out drilling on bench drilling
Theories: The student should explain:
- Safety precautions while performing the task.
- Safe handling of drilling tools and equipment. Proper waste disposal
Swali
Which part of a bench drilling machine holds the drill bit firmly in place?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado