Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Counterboring drilled holes
Hand drilling on a plate is a fundamental skill in workshop practice. It involves using a portable drilling machine held and operated by hand to create round holes in metal, wood, or plastic materials. This skill is essential for repairs, maintenance, and fabrication work in agro-mechanics.
Hand drilling refers to the use of a small portable drilling machine that is held and operated by hand. The machine uses a rotating drill bit to cut or enlarge a hole in a solid material. The drill bit rotates at high speed and is pressed into the workpiece to create a cylindrical hole that can pass partially (blind hole) or completely through (through hole) the material.
A drill machine is an electrical tool used for making round holes or driving fasteners. It is fitted with a twist drill bit secured in a chuck.
Cordless Drill
A cordless drill is electrical equipment operated by a battery fitted inside it. It is not connected to the electricity mains, making it more portable and convenient for fieldwork.
Electric Drill Machine
An electric drill is a power tool used to create cylindrical holes in a workpiece. The drill bit rotates at high speed and is pressed into the workpiece to create holes. It requires connection to a power supply through a cable.
Before performing hand drilling, gather the following:
- Hand drilling machine (cordless or electric)
- Drill bits of various sizes
- Work bench
- Bench vice
- Centre punch
- Scriber
- Steel rule
- Try square
- Hacksaw
- Wire brush
- Coolant or cutting oil
- Vernier caliper
- Cotton waste
- Material to be drilled (plate or flat bar)
Always wear the following protective equipment:
- Safety clear glasses or goggles
- Gloves
- Safety boots
- Overall
Always follow these safety rules before and during drilling:
-
Examine the machine – Make sure it is in good working order before using it.
-
Check the power supply – Examine the cable and plug for damage. Replace if necessary. Do not repair damaged cables yourself.
-
Keep cable clear – Keep the power supply cable away from the working area to prevent accidents.
-
Correct positioning – Hold the machine at right angles (90°) to the sheet being drilled.
-
Use correct chuck key – Use the correct size chuck key to secure the drill bit.
-
Secure the chuck key – Attach the chuck key to the lead with tape or non-conducting material. Ensure it does not cut into the insulation of the power lead.
-
Hold machine firmly – Grip the drilling machine securely before pressing the trigger switch.
-
Use support material – Place wooden strips underneath your workpiece to prevent damage to the workbench.
-
Handle carefully – Place the machine on the bench where it cannot be knocked down. Ensure nobody can trip over the power lead.
-
Secure small workpieces – Clamp small workpieces in a vice or on the workbench before drilling them.
Step 1: Prepare the Workpiece
- Select a flat bar or plate of suitable size (for example, 100mm × 100mm × 10mm)
- Clean the workpiece using cotton waste or a wire brush
- Measure and mark the positions where holes will be drilled using a steel rule and scriber
Step 2: Mark the Hole Positions
- Use a centre punch to create a small indentation at the centre of each marked hole position
- This indentation acts as a starting point for the drill bit and prevents it from wandering
Step 3: Select the Correct Drill Bit
- Choose the appropriate drill bit size for the required hole (for example, 3mm, 6mm, or 9mm diameter)
- Ensure the drill bit is sharp and in good condition
Step 4: Install the Drill Bit
- Insert the drill bit into the chuck of the drilling machine
- Use the chuck key to tighten and secure the drill bit firmly
Step 5: Position the Workpiece
- Secure the workpiece in a vice or clamp it firmly to the workbench
- Place wooden strips underneath to protect the workbench surface
Step 6: Start Drilling
- Hold the drilling machine at 90° to the workpiece surface
- Press the trigger switch to start the machine
- Lower the drill bit slowly onto the centre-punched indentation
- Apply steady, even pressure while allowing the drill bit to cut
- Use coolant or cutting oil when drilling metal to reduce heat and prolong drill bit life
Step 7: Complete the Hole
- Continue drilling until the drill bit passes completely through the material (for through holes)
- Release the trigger and wait for the drill bit to stop completely before removing it
Step 8: Clean Up
- Remove the workpiece from the vice
- Use a wire brush or cotton waste to remove metal chips and debris
- Check the hole size using a vernier caliper if needed
A student practices hand drilling by using a flat bar of 100mm × 100mm × 10mm. They need to drill three holes of different diameters:
- Hole 1: 3mm diameter
- Hole 2: 6mm diameter
- Hole 3: 9mm diameter
Procedure:
- Mark three positions on the plate, ensuring they are evenly spaced (for example, 25mm from each edge)
- Centre-punch each marked position
- Start with the smallest drill bit (3mm) – it requires less pressure and creates a pilot hole
- Change to the 6mm drill bit and drill the second hole
- Finally, use the 9mm drill bit for the largest hole
- After each hole, apply coolant to prevent overheating
- Verify each hole diameter using a vernier caliper
Important: Always drill smaller holes first before larger ones. This makes it easier to position subsequent holes accurately and reduces strain on the drill machine.
- Drill bit wanders – Ensure the centre punch mark is clear and start slowly
- Hole is too large – The drill bit may be loose; tighten the chuck properly
- Drill bit overheats – Apply coolant and reduce drilling speed
- Rough hole edges – Use a sharper drill bit or reduce feed pressure
In Tanzania, hand drilling skills are valuable for repairing and maintaining farm equipment such as ploughs, seed drills, and irrigation pumps. For example, a farmer in Morogoro might need to drill new holes in a damaged metal fence or repair agricultural tools using a hand drill. This skill also helps small workshop owners in towns like Arusha or Dodoma who repair motorcycles, bicycles, and farming implements, enabling them to earn income through practical repair services.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings.
- Select tools, equipment and materials
- Mark work piece.
- Drill holes
- Observe safety precautions
- Clean tools, equipment, work piece and work place
- Store tools, equipment
Tathmini ya matokeo
Hand drilling on plate performed as per provided worksheet
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Perform hand drilling on plate process
Principles: The the principles of: Performing hand drilling on plate Selection
Theories: The student should explain: hand drilling on plate procedures
- Safety precautions while performing the task.
- Safe handling of drilling tools and equipment. Proper waste disposal
Swali
What is hand drilling?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado