Mada za sehemu hiiPerforming tyres serviceMada 3
- Replacing worn tyres
- Repairing punctures
- Refilling tyres pressure
Replacing Worn Tyres
When a motorcycle tyre becomes worn out, it loses its ability to grip the road properly, which affects safety and handling. Replacing worn tyres is an essential maintenance skill that every motorcyclist should know. This process involves removing the old tyre and installing a new one that is appropriate for the motorcycle.
- Reduced tread depth: The tread pattern wears down, decreasing grip on wet and dry roads
- Poor braking performance: Worn tyres increase stopping distance
- Risk of punctures: Thinner rubber is more likely to be damaged by sharp objects
- Unstable handling: Worn tyres can cause the motorcycle to sway or vibrate
- Legal requirements: Tyres must meet minimum tread depth regulations
Before starting, gather the following:
- New tyre (correct size for the motorcycle)
- Tyre levers
- Rim protectors
- Wrench set or socket set
- Tyre pressure gauge
- Air compressor or foot pump
- Service manual for the motorcycle
- Soapy water or tyre lubricant
- Clean cloth
Always observe these safety measures:
- Wear safety boots and overalls to protect yourself
- Ensure the motorcycle is on a stable stand or platform
- Work in a clean, well-lit area
- Never use damaged or incorrect tools
- Check the new tyre for visible defects before installation
Step 1: Prepare the Motorcycle
- Park the motorcycle on a level, stable surface
- Engage the centre stand or use a paddock stand
- Loosen the wheel axle nuts slightly before lifting the wheel
Step 2: Remove the Wheel
- Remove the axle nut and washers
- Carefully lift the wheel from the fork or swingarm
- Place the wheel on a clean surface
Step 3: Remove the Old Tyre
- Let out all air from the tyre by pressing the valve stem
- Insert the tyre lever under the tyre bead, away from the valve
- Use additional levers to work around the tyre, pushing the bead over the rim edge
- Remove the inner tube carefully
- Pull the tyre off the rim completely
Step 4: Inspect the Rim and Components
- Check the rim for cracks, dents, or damage
- Inspect the inner tube for punctures or signs of wear
- Clean the rim and check that the rim tape is in good condition
Step 5: Install the New Tyre
- Apply a thin layer of soapy water or tyre lubricant to the tyre beads and rim
- Place the new tyre on the rim, starting with the valve stem hole
- Push the tyre beads over the rim edge using tyre levers
- Ensure both beads are seated properly on the rim
Step 6: Install the Inner Tube
- Partially inflate the inner tube to give it shape
- Insert the tube inside the tyre, ensuring it sits properly
- Make sure the valve stem is aligned with the rim hole
Step 7: Inflate the Tyre
- Attach the air compressor or pump to the valve stem
- Inflate the tyre to the recommended pressure
- Check the pressure using a tyre pressure gauge
Step 8: Reinstall the Wheel
- Lift the wheel back into position
- Insert the axle and secure with washers and nut
- Tighten the axle nut to the specified torque
Step 9: Final Check
- Inspect the tyre to ensure it is seated correctly
- Check that the wheel spins freely without rubbing
- Verify tyre pressure after a short test ride
A motorcycle tyre has a recommended pressure of 2.2 bar (32 PSI). After installing a new tyre, the pressure gauge reads 1.8 bar. How much more air is needed?
The tyre should be inflated to 2.2 bar. Current reading is 1.8 bar.
Additional pressure needed = 2.2 - 1.8 = 0.4 bar
The rider should add 0.4 bar (approximately 6 PSI) to reach the correct pressure.
- Always refer to the service manual for correct tyre size and pressure
- Replace both tyres at the same time if both are worn
- Check wheel alignment after tyre replacement
- Inspect the tyre pressure regularly after installation
In Tanzania, motorcycle taxis (bodaboda) are a common form of transport in many towns like Mwanza, Arusha, and Dodoma. A bodaboda rider who knows how to replace worn tyres can save money by doing the work themselves instead of paying a mechanic around TSh 10,000 to 15,000 per tyre. This skill also means the rider can quickly fix a worn tyre and get back to work, maintaining their daily income without long delays at a garage.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Use service manual
- Select tools and equipment
- Test tyre
- Observe safety precautions
- Store clean tools, equipment and workplace
- Store tools and equipment
- Properly dispose wastes 100
Tathmini ya matokeo
Worn tyres replaced as per manufactures guideline knowledge Detailed knowledge about:
- Safety precautions while replacing worn tyres.
- Safe handling of tools and equipment
Tathmini ya maarifa
Knowledge evidence: Detailed
Method used: The student should explain how to: Replacing worn tyres.
Principles: The explain principles of:
- Replace/refix
Theories: The explain ways of replacing worn
Swali
Which of the following is a reason for replacing a worn motorcycle tyre?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado