Mada za sehemu hiiPerforming butt fusion weldingMada 1
- Performing butt fusion welding
Butt fusion welding joins two plastic pipes end to end. The two pipe ends are heated against a hot plate until they melt, then pressed together and held until the joint cools. A good joint is as strong as the pipe itself, which is why this method is used for water supply and irrigation mains.
- Butt fusion: joining two pipe ends of the same diameter and wall thickness by melting them and pressing them together.
- Heater plate (hot plate): an electrically heated plate with a non-stick surface that melts the pipe ends.
- Facing tool (planer or peeler): a rotating cutter that shaves both pipe ends until they are clean, flat and parallel.
- Bead: the ring of melted plastic that rolls out on each side of the joint.
- Drag pressure: the pressure needed just to make the machine carriage move with the pipe clamped in it.
- Fusion pressure: the gauge pressure used to press the two melted ends together.
Butt fusion is used on thermoplastics, which soften when heated and harden again when cooled:
- Polyethylene (PE, HDPE): the most common, used for water, gas and irrigation pipes
- Polypropylene (PP): used for industrial and hot-water pipes
- PVDF and PB: special pipes for chemicals and hot water
Only pipes of the same material, the same outside diameter and the same wall thickness are joined to each other.
| Type | How pressure is applied | Used for |
|---|---|---|
| Manual (mechanical) | By hand, with a lever or screw and a spring gauge | Small pipes |
| Hydraulic | By a hydraulic pump and cylinders; pressure is read on a gauge | Medium and large pipes |
| Automatic (CNC) | By a controller that sets and records every stage | Work where each joint must be recorded |
A data logger records the temperature, pressures and times of each joint so that the joint can be checked later.
- Butt fusion machine with clamp inserts for the pipe size, heater plate and facing tool
- Hydraulic unit and hoses
- Hacksaw or pipe cutter, scraper, steel rule or tape measure
- Clean lint-free cloth
- Heat-resistant leather gloves, clear goggles, overall, leather apron, safety boots and helmet
The pipe ends must be pressed together with the right force. Too little gives a weak joint; too much squeezes the melted plastic out of the joint.
The gauge pressure is worked out in three steps:
- Area of the pipe end = 3.14 ÷ 4 × (outside diameter² − inside diameter²)
- Force needed = area of the pipe end × interfacial pressure. For polyethylene the interfacial pressure is about 0.15 N/mm² (use the value in the pipe maker's table).
- Gauge pressure = force ÷ total piston area of the machine's cylinders, plus the drag pressure.
Using a fusion pressure calculator
Machine makers give a table, a chart or a phone or computer calculator for their machines. To use it:
- Choose the machine model
- Enter the pipe outside diameter and its wall thickness (or SDR)
- Read the fusion pressure it gives
- Measure the drag pressure on the machine and add it
- Prepare. Read the machine manual and the pipe maker's welding table. Check that the heater plate is clean and at the temperature in the table (for polyethylene usually between 200 °C and 230 °C).
- Clamp. Cut the pipe ends square, wipe them clean inside and outside, and clamp both pipes in the machine with a little pipe sticking out of each clamp.
- Measure the drag pressure. Move the carriage slowly and read the pressure at which it just moves.
- Face the ends. Put the facing tool between the pipes and press the ends against it until a continuous shaving comes off both ends. Remove the tool and the shavings. Do not touch the faced ends.
- Check alignment. Bring the ends together. There should be no visible gap, and the pipe walls should line up all round. Adjust the clamps and face again if needed.
- Heat. Put the heater plate between the ends and press them against it at fusion pressure until a small bead forms all round. Then lower the pressure to the drag pressure and let the heat soak in for the time in the table.
- Change over. Open the carriage, take the plate out and close the carriage again as quickly as possible, without bumping the ends together.
- Join. Raise the pressure smoothly to the fusion pressure and hold it.
- Cool. Keep the joint under pressure, without moving it, for the cooling time in the table. Never cool the joint with water.
- Release and record. Release the pressure, open the clamps and write down or save the joint record.
A good joint has:
- A bead that goes all round the pipe, the same size all the way
- Two rounded rolls of about the same size, with the groove between them not going below the pipe surface
- Pipe walls that line up, with no step at the joint
- No gaps, bubbles, dirt or cracks in the bead
| Fault | Likely cause | Remedy |
|---|---|---|
| Bead too small | Plate too cool, heating time too short, pressure too low | Check the temperature and follow the table |
| Bead too large | Too much pressure or heating time too long | Reduce to the values in the table |
| Bead uneven round the pipe | Pipes not aligned, ends not faced flat | Re-clamp and face again |
| Bubbles or pits in the bead | Wet or dirty pipe ends, plate too hot | Dry and clean the ends, check the temperature |
| Joint breaks cleanly (cold joint) | Change-over too slow, plate too cool | Cut out the joint and weld again |
| Dirt in the joint | Ends touched or dusty after facing | Face again and keep the ends clean |
A faulty joint is never repaired. It is cut out and a new joint is made.
- The heater plate is hot enough to cause deep burns. Handle it by its handle, wear heat-resistant gloves and keep it in its stand when it is not in use.
- Keep hands out of the carriage and clamps when the hydraulics are moving.
- The facing tool has sharp blades. Switch it off and let it stop before removing it.
- Keep electrical cables dry and undamaged, and do not weld in the rain without a shelter.
- Lift heavy pipes with a partner or with lifting equipment.
- Work where fresh air can carry away fumes from the hot plastic.
- Wipe the heater plate with a clean dry cloth while it is still warm; never scrape it with metal
- Clean the facing tool and clamps and store the machine dry, with the heater plate in its guard
- Collect plastic shavings and pipe off-cuts for recycling or the waste bin
- Wipe up any hydraulic oil and put oily rags in a covered bin
A polyethylene pipe has an outside diameter of 110 mm and a wall thickness of 10 mm, so its inside diameter is 90 mm. The machine's cylinders have a total piston area of 500 mm². The drag pressure measured is 5 bar.
- Area of the pipe end = 3.14 ÷ 4 × (110² − 90²) = 0.785 × (12,100 − 8,100) = 0.785 × 4,000 = 3,140 mm²
- Force needed = 3,140 × 0.15 = 471 N
- Pressure from the force = 471 ÷ 500 = 0.94 N/mm², which is about 9.4 bar
- Gauge pressure = 9.4 + 5 = 14.4 bar
Villages and farms lay polyethylene mains to bring water from a spring, borehole or dam to taps and fields. A technician who can butt fuse the pipe lengths on site makes one continuous, leak-free line with no mechanical couplings to work loose, so less water is lost and the line needs little repair.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Select tools and equipment.
- Use butt fusion equipment
- Perform Butt fusion welding
- Inspect weld metal defects.
- Observe safety precautions.
- Clean tools, equipment and work place.
- Store tools and equipment.
Tathmini ya matokeo
Welded work piece conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to apply Butt fusion welding techniques.
Principles: Students should explain the principle of:
- Determining Fusion Pressure
Theories: Students should explain:
- Types of Butt fusion welding machine.
- Hydraulic Butt Fusion Machine Procedure.
- Types of materials for Butt fusion welding.
- Butt Fusion Joint Troubleshooting
- How to Use the Fusion Pressure Calculator
- Butt fusion welding.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing Butt fusion welding
- Safe handling of work tool, equipment and work place.
- Waste disposal
Swali
What is the main purpose of the facing tool in butt fusion welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado