Mada za sehemu hiiPerforming maintenance of tillage machineryMada 6
Servicing Secondary Tillage Implements
Secondary tillage implements prepare the soil after primary tillage by breaking up clods, leveling the surface, and controlling weeds. Regular servicing keeps these implements working efficiently and extends their useful life, reducing costly breakdowns during planting season.
Secondary tillage implements are machines used after primary tillage to create a fine, smooth seedbed suitable for planting. They work at shallower depths than primary implements—typically 5 to 15 centimetres—and focus on soil refinement rather than deep loosening.
Common secondary tillage implements include:
- Disc harrows – consist of several concave discs that cut and break up soil clods
- Spring tooth harrows – have flexible tines that stir the soil and remove weeds
- Rotavators – use rotating blades to pulverize soil
- Ridgers – form raised beds or furrows for planting
- Field rollers – compact and level the soil surface
These implements improve soil aeration, help control weeds, and create a firm seedbed where seeds can make good contact with moist soil.
Proper servicing of secondary tillage implements:
- Ensures consistent seedbed quality
- Prevents uneven tillage that affects crop emergence
- Reduces fuel consumption during operation
- Extends the life of blades, tines, and bearings
- Prevents field delays caused by equipment failure
Follow these systematic steps when servicing secondary tillage implements:
Step 1: Pre-operation Check and Cleaning
Before servicing, perform pre-operation checks on both the tractor and the implement. Then clean the implement thoroughly:
- Use a pressure washer or wire brush to remove soil, debris, and rust
- Pay special attention to blades, tines, and the frame
- Allow the implement to dry before inspection
Step 2: Inspect for Wear and Damage
Carefully examine all components:
- Blades and tines – check for wear, cracks, or bending
- Harrows – inspect each tooth for damage
- Frame and hitch – look for cracks or bent sections
- Fasteners – identify any loose or missing bolts and nuts
If blades or tines are dull, sharpen them using a sharpening file. Replace severely worn or damaged parts.
Step 3: Tighten Fasteners and Lubricate
- Use a spanner or socket set to tighten all bolts, nuts, and fasteners
- Ensure proper alignment of blades, tines, and disc gangs
- Apply grease to all moving joints and pivot points using a grease gun
- Lubricate bearings to reduce friction and prevent premature wear
Step 4: Check Hydraulic System (if applicable)
If the implement has hydraulic components:
- Inspect hydraulic hoses for cracks, leaks, or wear
- Check hose connectors for damage
- Replace any damaged hoses or connectors to prevent fluid leaks
Step 5: Inspect Wheels and Tyres (if equipped)
- Check wheel bearings for play or damage
- Verify tyre pressure is correct
- Replace worn bearings or repair tyre problems
Step 6: Reassemble and Test
After servicing:
- Reassemble any removed components securely
- Adjust settings (depth, angle) as needed for the soil conditions
- Test the implement at low speed before full field operation
- Observe for unusual vibrations, noises, or misalignment
A disc harrow has been used to prepare a seedbed but shows signs of poor performance—the discs are not cutting evenly and soil clods remain large.
Diagnosis:
- Blades are dull and need sharpening
- Some disc angles have shifted, causing uneven working
- Several bolts have loosened from field vibration
Servicing steps performed:
- Cleaned all soil from disc edges and frame using a wire brush
- Inspected each disc for wear—two discs needed replacement
- Sharpened remaining dull blades with a sharpening file
- Tightened all bolts and adjusted disc angle to match manufacturer specifications
- Greased all pivot points and bearings
- Tested at low speed—all discs rotating evenly
The harrow now works properly, producing a fine seedbed.
When servicing secondary tillage implements:
- Wear safety goggles, gloves, boots, and overalls
- Ensure the implement is stable and supported before working underneath
- Disconnect the tractor before servicing
- Allow moving parts to stop completely before inspection
In Tanzania, smallholder farmers often hire tractors with attached harrows to prepare their fields before planting maize or rice. A well-serviced harrow works faster and uses less fuel, which means the farmer pays less for land preparation. For example, if a disc harrow with worn blades requires two passes instead of one to achieve a fine seedbed, the farmer spends approximately TSh 50,000–80,000 extra per acre in fuel and labour. Knowing how to service these implements helps farmers and agro-mechanics reduce costs and plant on time.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret drawings.
- Select tools and equipment.
- Conduct inspection on secondary tillage machines.
- Service tillage secondary implements.
- Perform relevant adjustments on tillage machines.
- Observe safety precautions
- Clean tools, equipment and work place.
- Store tools and equipment’s
Tathmini ya matokeo
Serviced secondary tillage machines conform to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Conduct adjustments on tillage machine.
- Replace worn out parts.
- Service different tillage machines.
Principles: Students should explain the principle of:
- Servicing different secondary implements.
Theories: Students should explain:
- Repair of different secondary tillage implements. Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while servicing secondary tillage machinery.
- Safe handling of working tools and equipment’s.
- Waste disposal.
Swali
What is the primary purpose of secondary tillage implements in soil preparation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado