Mada za sehemu hiiServicing milking machinesMada 6
Carrying out Adjustments on Milking Machines
A milking machine must be properly adjusted to extract milk efficiently while keeping the animal comfortable and protecting udder health. The main adjustments focus on vacuum pressure, pulsation settings, and physical positioning of the milking cluster.
Proper adjustments prevent udder damage, ensure milk quality, and maximize milking efficiency. Incorrect settings can cause discomfort to the animal, reduce milk output, or lead to mastitis.
The vacuum level is the suction force that pulls milk from the teat. It must be set within the correct range to be effective yet gentle.
Key Points
- Correct vacuum range: 38–42 kPa (approximately 11.4–12.7 millimetres of mercury)
- Use a vacuum gauge to measure the pressure
- Turn the middle part of the vacuum regulator to increase or decrease pressure
- The system must maintain a stable vacuum during operation
Signs of Incorrect Vacuum
| Problem | Possible Cause |
|---|---|
| Vacuum too high | Teat damage, liner slip |
| Vacuum too low | Incomplete milk removal |
| Fluctuating vacuum | Air leaks, blocked air admission holes |
Pulsation creates a squeeze-and-release action that mimics calf suckling. It has two phases:
- Milking phase (massage phase): About 60% — liner is open, milk flows
- Rest phase: About 40% — liner is closed, blood circulates
Settings to Check
- Pulsation rate: 60–70 cycles per minute
- Pulsation ratio: Approximately 60:40 (milking to massage)
How to Check
Place thumbs inside test cup liners and feel the pulsator action. The squeeze-to-release time should feel balanced. Also listen for a steady pulsing sound.
Daily Checks
- Ensure air admission holes in the claw piece are unblocked
- Listen for hissing from the regulator — this sound should decrease when the cluster is attached
- Check liners and hoses for air leaks
The milking cluster must hang correctly under the udder to ensure even milk flow and prevent injury.
Proper Positioning
- The four teat cups should be aligned vertically under each teat
- The claw outlet should point between the cow's legs
- All hoses must be untwisted to allow smooth milk and air flow
Common Problem: Twisted Hoses
When hoses twist, a "square position" forms under the udder. This creates uneven vacuum and can cause liner slip or teat damage.
Alignment Checks
- Ensure short milk tube and liner markings on the hood are aligned
- Adjust the unit to minimize liner slip during milking
- Check that hoses do not kink or block milk flow
After adjusting vacuum and pulsation, verify that milk flows smoothly.
What to Check
- Ensure milk lines are clear of blockages
- Check for slow or incomplete milk flow
- Inspect air admission valves or ports on liners to ensure they provide the correct amount of air during the massage phase
Modern milking machines have automated systems that control vacuum, pulsation, and milk flow. These must be calibrated according to the manufacturer's guidelines.
Steps
- Verify settings for vacuum and pulsation match recommended values
- Test milk flow sensors
- Check that automated cluster removers activate correctly
After making any adjustments, always run a test cycle:
- Attach the cluster to a cow or test unit
- Observe vacuum stability and milk flow
- Check that teat cups fit properly without slipping
- Listen for unusual sounds from the pulsator or regulator
Documentation
Record all adjustments made, including:
- Vacuum pressure readings
- Pulsation rate and ratio
- Parts replaced
- Any issues identified
A farmer notices that milk flow is slow and incomplete during milking. Using a vacuum gauge, you measure the vacuum at the claw and find it is only 32 kPa.
Steps to fix:
- Check the vacuum regulator — turn the adjustment screw clockwise to increase pressure
- Set the gauge to read within 38–42 kPa range
- Check all connections and hoses for air leaks
- Ensure the air admission holes in the claw are not blocked
- Run a test milking to confirm proper milk flow is restored
In Tanzania, smallholder dairy farmers using milking machines at cooperatives or milk collection centers rely on proper machine adjustments to maintain milk quality and prevent spoilage. For example, a farmer in Mwanza with two dairy cows can apply these adjustment skills to ensure the milking machine operates efficiently, producing clean milk that sells at local markets for up to TSh 1,500 per litre without rejection due to poor quality.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret drawings.
- Select tools and equipment.
- Inspect milking machines
- Perform adjustments on machines
- Observe safety precautions.
- Clean tools and equipment.
- Store tools and equipment.
Tathmini ya matokeo
Adjusted milking machines conform to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Carry out adjustments on milking machines
- Operate milking machines.
Principles: Students should explain the principle of:
- Carrying out adjustments on milking machines
Theories: Students should explain:
- Types of milking machines.
- Types of small scale milking machines.
- Function of milking machine components.
- Operation of milking plants.
- Effects of heat in milk storage.
- Effect of pressures in milking system.
- Effects of vacuum in milking system.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precaution while servicing milking machines.
- Safe handling of working tools and equipment.
- Waste disposal.
Swali
What is the correct vacuum level range for a milking machine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado