Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Counterboring drilled holes
Carrying Out Drilling on Bench Drilling Machine
A bench drilling machine is a stationary tool used to create accurate holes in metal, wood, or plastic. It is commonly found in agro-mechanics workshops for repairing farm equipment and fabricating metal parts.
A bench drilling machine, also called a bench drill press, is mounted securely on a workbench or stand. It uses a rotating drill bit to cut cylindrical holes through materials. The machine provides stability and precision that hand drilling cannot achieve.
The bench drilling machine has several important parts:
- Fixed Position: The machine is securely mounted, making it stable during operation.
- Drill Head: Houses the motor and spindle that holds the drill bit. It moves up and down to control drilling depth.
- Work Table: A flat surface that can be adjusted in height and tilted for different drilling angles.
- Chuck: A three-jaw or four-jaw device that securely holds the drill bit in place.
- Depth Stop: Allows you to set the exact drilling depth for uniform holes.
- Speed Control: Some machines offer variable speed settings for different materials and hole sizes.
Before starting, gather these tools and materials:
- Bench drilling machine
- Drill bits (appropriate size for the hole needed)
- Workbench
- Bench vice
- Centre punch
- Hammer
- Scriber
- Steel rule
- Try square
- Vernier calliper
- Oil can (for lubrication)
- Wire brush
- Cotton waste
- Coolant (optional, for metal drilling)
Always follow these safety rules when using the bench drilling machine:
- Wear appropriate Personal Protective Equipment (PPE): safety boots, overalls, leather gloves, and safety goggles.
- Examine the machine before use to ensure it is in good working order.
- Check the power supply cable and plug for damage. Replace if necessary.
- Keep the power cable clear of the working area.
- Hold the machine at right angles (90°) to the workpiece.
- Secure the workpiece firmly to the work table using a vice or clamps.
- Use wooden strips underneath the workpiece to prevent damage to the workbench.
- Keep hands away from the drill bit while the machine is running.
- Switch off the machine when changing drill bits or adjusting the workpiece.
Follow these steps to drill a hole using a bench drilling machine:
Step 1: Prepare the Workpiece
- Measure and mark the position of the hole using a steel rule, scriber, and try square.
- Use a centre punch to make a small indentation at the centre of the marked position. This guides the drill bit and prevents it from wandering.
Step 2: Select and Install the Drill Bit
- Choose the correct drill bit size for the hole you need.
- Loosen the chuck using the chuck key.
- Insert the drill bit into the chuck and tighten securely.
Step 3: Secure the Workpiece
- Clamp the workpiece firmly to the work table using a vice.
- Ensure the workpiece is properly aligned with the drill bit position.
Step 4: Set the Drilling Depth
- Adjust the depth stop to set the required drilling depth.
- This ensures all holes drilled are the same depth.
Step 5: Position the Workpiece
- Lower the drill head by turning the feed handle.
- Align the drill bit with the centre punch mark on the workpiece.
Step 6: Start Drilling
- Switch on the machine.
- Lower the drill head slowly and steadily by turning the feed handle or lever.
- Maintain firm pressure and control throughout the drilling process.
- Apply cutting oil periodically to reduce heat and extend drill bit life.
Step 7: Complete and Finish
- After the drill bit penetrates completely, raise the drill head.
- Switch off the machine and wait for the drill bit to stop completely.
- Remove the workpiece carefully.
- Clean any metal chips or debris from the workpiece.
A farmer needs to repair a damaged fertilizer spreader by drilling a 10 mm diameter hole in a 6 mm thick flat bar to attach a new bolt. The following procedure is used:
- Mark the hole position at 30 mm from the edge of the flat bar using a steel rule and scriber.
- Use a centre punch to make a starting point at the marked position.
- Select a 10 mm diameter twist drill bit and install it in the chuck.
- Clamp the flat bar securely in a bench vice on the drill table.
- Set the depth stop to 6 mm to match the material thickness.
- Switch on the machine and lower the drill bit slowly.
- Apply cutting oil while drilling to keep the bit cool.
- Raise the drill bit, switch off the machine, and remove the flat bar.
- Use a wire brush to clean metal chips from the hole.
The hole is now ready for the bolt to be inserted during the repair of the fertilizer spreader.
In Tanzanian agro-mechanics workshops, a bench drilling machine is used to create holes when repairing and maintaining farm equipment such as ploughs, planters, and harvesters. For example, when a local mechanic at a market in Arusha needs to attach a new bracket to a water pump housing, they would use the bench drilling machine to accurately drill holes for bolts, ensuring the pump is securely reassembled and functions properly for farmers who rely on it for irrigation.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools, equipment and materials.
- Mark work piece.
- Cut work piece to size.
- Perform drilling.
- Observe safety precautions
- Clean tools, equipment and work place.
- Store tools, equipment and work piece.
Tathmini ya matokeo
Drilled hole conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Perform drilling process.
- Calculate drill size and drilling speed.
Principles: Students should explain the principles of:
- Drilling.
- Selection of drilling speed.
Theories: Students should explain:
- Drilling procedures.
- Purpose of coolant in drilling process.
- Materials used to manufacture drill bits.
- Drill bit cutting angles.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing drilling.
- Safe handling of tools and equipment.
- Waste disposal.
Swali
What is the primary purpose of a bench drilling machine in an agro-mechanics workshop?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado