Mada za sehemu hiiPerforming drillingMada 3
- Performing hand drilling on plate
- Carrying out drilling on bench drilling machine
- Counterboring drilled holes
Performing Hand Drilling on Plate
Hand drilling is a process of creating holes in metal, wood, or plastic materials using a portable drilling machine that is held and operated by hand. A drill machine is an electrical tool used for making round holes by rotating a twist drill bit against the workpiece. The drilling process involves pressing a rotating drill bit into the material to cut a cylindrical hole that can pass partially or completely through the workpiece.
In agro-mechanics, hand drilling is commonly used for repair and maintenance of agricultural equipment such as fixing holes in metal frames, attaching brackets, or creating openings for fasteners in farming machinery.
Cordless Drill
A cordless drill is electrical equipment operated by a battery fitted inside it. It is not connected to the electricity mains, making it portable and convenient for working in areas without easy access to power outlets.
Electric Drill Machine
An electric drill machine is a power tool used to create cylindrical holes in a workpiece. The drill bit rotates at high speed and is pressed into the material to create a hole. This type of drill is commonly used in workshop settings where a power supply is available.
| Category | Items |
|---|---|
| Tools/Equipment | Oil can, work bench, drill bits, bench vice, hand drill machine |
| Materials | Oil, cotton waste, workpiece (metal plate), drill bits |
| Safety Gears | Safety boots, overalls, leather gloves, safety goggles |
Always follow these safety precautions before operating a hand drill:
- Examine the machine and make sure it is in good working order before using it.
- Check the power supply cable and plug for damage and replace if necessary. Do not repair damaged cables.
- Keep the power supply cable clear of the working area to prevent accidents.
- Hold the machine at right angles (90°) to the sheet being drilled.
- Use the correct size chuck key for securing the drill bit.
- Secure the chuck key to the lead with tape or any other non-conducting material. Make sure it does not cut into the insulation of the power lead.
- Hold the drilling machine securely before pressing the trigger switch.
- Use wooden strips underneath your workpiece to prevent damage to the workbench.
- Handle the machine carefully and place it on the bench in such a way that it can't be knocked down, and that nobody can trip over the power lead.
- Clamp small workpieces in a vice or on the workbench before drilling them.
Step 1: Prepare the Workpiece
Select a flat bar material of suitable size (for example, 100mm × 100mm × 10mm). Clean the workpiece using cotton waste and apply a small amount of oil if needed to protect the surface.
Step 2: Mark the Hole Position
Use a scriber and steel rule to mark the exact position where the hole will be drilled. A centre punch is then used to create a small indentation at the centre of the marked position. This indentation serves as a starting point for the drill bit and prevents it from slipping.
Step 3: Secure the Workpiece
Clamp the workpiece firmly to the workbench using a bench vice. For additional protection, place wooden strips underneath the workpiece. Ensure the workpiece is stable and will not move during drilling.
Step 4: Select and Install the Drill Bit
Choose the correct drill bit size for the required hole diameter. For practice, you may start with a 3mm drill bit, then progress to 6mm and 9mm diameters. Insert the drill bit into the chuck and tighten securely using the chuck key.
Step 5: Position the Drill Machine
Hold the drilling machine at right angles (90°) to the workpiece surface. Position the drill bit directly over the centre punch mark.
Step 6: Begin Drilling
Press the trigger switch to start the drill. Apply steady, even pressure as the drill bit penetrates the material. Let the drill do the work — excessive pressure may break the drill bit or damage the workpiece.
Step 7: Complete the Hole
Continue drilling until the drill bit passes completely through the workpiece, creating a through hole. For a blind hole, stop at the desired depth.
Step 8: Finish and Clean Up
Switch off the drill and wait for the drill bit to stop completely before removing it from the workpiece. Remove the workpiece from the vice and clean any metal chips or debris using cotton waste. Apply oil to prevent rust on metal workpieces.
A student practices hand drilling on a 100mm × 100mm × 10mm flat bar. The task is to drill three holes with diameters of 3mm, 6mm, and 9mm.
Procedure followed:
- Mark three positions on the flat bar using a steel rule and scriber, ensuring equal spacing.
- Use a centre punch to create starting points for each hole.
- Secure the flat bar in a bench vice.
- Start with the 3mm drill bit, drill the first hole, then change to the 6mm drill bit for the second hole, and finally use the 9mm drill bit for the third hole.
- Clean the holes and the workpiece after drilling.
This practice develops skills in:
- Accurate marking and centering
- Using different drill bit sizes
- Controlling drilling speed and pressure
- Clean the drill machine regularly to remove dust and metal filings.
- Check the drill bits for sharpness and replace dull or damaged bits.
- Inspect the power cable and plug for any damage before each use.
- Apply oil to moving parts of the drill machine to ensure smooth operation.
- Store tools in a dry place to prevent rust and damage.
In Tanzania, hand drilling skills are used by local mechanics and farmers to repair agricultural equipment such as ploughs, irrigation pumps, and storage containers. For example, when a farmer needs to attach a new bracket to a water tank at a farm in Morogoro, they would use a hand drill to create holes for bolts, enabling quick and effective repair without traveling to a workshop.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools, equipment and materials.
- Mark work piece.
- Cut work piece to size.
- Perform drilling.
- Perform reaming.
- Observe safety precautions
- Clean tools, equipment and work place.
- Store tools, equipment and work piece.
Tathmini ya matokeo
Drilled hole conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Perform drilling process.
- Calculate drill size and drilling speed.
Principles: Students should explain the principles of:
- Drilling.
- Selection of drilling speed.
Theories: Students should explain:
- Drilling procedures.
- Purpose of coolant in drilling process.
- Materials used to manufacture drill bits.
- Drill bit cutting angles.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing drilling.
- Safe handling of tools and equipment.
- Waste disposal.
Swali
What is the correct angle at which a hand drilling machine should be held relative to the workpiece surface?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado