Mada za sehemu hiiConstructing operational amplifier circuitsMada 2
- Building photo switching circuit
- Building temperature-sensitive switching circuit
Photo Switching Circuit
A photo switching circuit is an electronic circuit that detects changes in light intensity and automatically switches a load (such as a lamp or buzzer) ON or OFF. It uses a light-dependent resistor (LDR) as the light-sensing element.
- Light Dependent Resistor (LDR): A resistor whose resistance decreases when light falls on it. In darkness, its resistance is high (about 1 MΩ); in bright light, it drops to about 100 Ω.
- Operational Amplifier (Op-Amp): Used as a comparator to compare two voltages and produce a digital output.
- Reference Voltage: A fixed voltage that sets the light-level threshold for switching.
- Relay: An electromagnetic switch that allows a small circuit to control a larger load.
- Power Supply: Provides the required DC voltage (usually +12V or +9V).
- The LDR is connected in a voltage divider arrangement with a fixed resistor.
- As light intensity changes, the LDR resistance changes, which changes the voltage across it.
- This variable voltage is fed to one input of the op-amp comparator.
- The op-amp compares the LDR voltage to the fixed reference voltage.
- When the LDR voltage goes above or below the reference (depending on circuit design), the op-amp output changes state.
- This output drives the relay, which switches the load ON or OFF.
+Vcc
|
[R1]
|-----> Non-inverting input (+)
|
[LDR]
|
|-----> Inverting input (-)
|
[R2]
|
GND
Where:
- R1 is a fixed resistor (typically 10 kΩ)
- R2 is a preset resistor (typically 10 kΩ) for adjusting sensitivity
- LDR is the light sensor
- Gather components: LDR, LM741 op-amp, relay (5V or 12V), resistors, LED or lamp for indicator, connecting wires, breadboard or PCB.
- Set up the voltage divider: Connect R1 (10 kΩ) in series with the LDR between Vcc and GND.
- Connect the op-amp: Connect the junction of R1 and LDR to the non-inverting input (+). Connect the inverting input (-) to a potential divider set to the reference voltage.
- Add feedback: Connect a feedback resistor between output and inverting input for hysteresis (optional but recommended).
- Connect the relay driver: Use a transistor (like BC547) between the op-amp output and relay coil to provide enough current.
- Connect the load: Connect the lamp or LED to the relay contacts.
- Test: Cover the LDR (darkness) and observe the load switching ON. Expose to light and observe it switching OFF.
A student builds a photo switching circuit to automatically turn on a 60W street lamp when it gets dark. The LDR in darkness has resistance of 500 kΩ, and in bright light has resistance of 200 Ω. Using a 10 kΩ series resistor and +12V supply:
In dark condition:
- Total resistance = 500 kΩ + 10 kΩ = 510 kΩ
- Current = V/R=12V/510kΩ≈0.024mA
- Voltage across LDR = 0.024mA×500kΩ≈12V
In bright light:
- Total resistance = 200 Ω + 10 kΩ = 10.2 kΩ
- Current = 12V/10.2kΩ≈1.18mA
- Voltage across LDR = 1.18mA×200Ω≈0.24V
The op-amp compares these voltages to the reference. When the LDR voltage drops below the reference (dark), the output goes HIGH and switches the lamp ON.
- Always disconnect power before assembling or modifying the circuit.
- Wear gloves and safety boots when working with electrical equipment.
- Ensure the work bench is clean and free of conductive materials.
- Use appropriate rating components for the load you are switching.
- Keep fingers away from live terminals during testing.
- If the circuit does not switch, check all connections and ensure the op-amp is getting power.
- If the LED flickers, adjust the reference voltage using the preset resistor.
- If the relay does not activate, verify the transistor is correctly wired.
- Test each section of the circuit individually using a multimeter.
In Tanzania, photo switching circuits are commonly used for automatic street lighting in towns like Arusha and Dodoma, where street lamps automatically turn ON at sunset and OFF at sunrise. A small entrepreneur in Dar es Salaam could build a simple version to automatically control outdoor security lights around a shop or home, saving electricity and providing security without manual switching.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and electronic components
- Construct circuit using operational amplifier
- Test performance of circuit
- Record test results
- Interpret test results
- Observe safety regulations
Tathmini ya matokeo
Constructed circuit functions as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct electronic circuits using operational amplifiers
Principles: The student should explain the principles of:
- Identifying IC pins
- Connecting ICs
Theories: The student should explain:
- Difference between integrated circuit and discrete component circuit
- Advantages of using integrated circuits (ICs)
- Applications of operational amplifier ICs
- Photo switching circuit
- Temperature sensitive switching circuit
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions in electronics work
- Safe handling of tools, equipment and components.
Swali
What is the main function of a photo switching circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado