Mada za sehemu hiiConstructing operational amplifier circuitsMada 2
- Building photo switching circuit
- Building temperature-sensitive switching circuit
A temperature-sensitive switching circuit is an electronic circuit that automatically turns a load on or off when the temperature reaches a set value. It uses a temperature sensor (thermistor) and an operational amplifier as a comparator to control a switching device like a relay.
What is a Temperature-Sensitive Switching Circuit?
A temperature-sensitive switching circuit, also called a temperature-controlled switch, is a circuit that detects changes in temperature and switches a load (such as a fan, heater, or alarm) on or off when the temperature crosses a threshold. These circuits are widely used in safety devices and climate control systems.
The main parts are:
- Thermistor – a resistor whose resistance changes with temperature (NTC: resistance decreases as temperature increases)
- Operational Amplifier (Op-Amp) – used as a voltage comparator to compare the temperature sensor voltage with a reference voltage
- Switching device – a transistor or relay that turns the load on or off
- Load – the device being controlled (fan, lamp, buzzer, etc.)
How the Circuit Works
-
The thermistor is connected in a voltage divider circuit with a fixed resistor. As temperature changes, the thermistor's resistance changes, which changes the voltage at the non-inverting input (+) of the op-amp.
-
A potentiometer (or fixed resistor) sets a reference voltage at the inverting input (−) of the op-amp. This reference voltage corresponds to the desired switching temperature.
-
The op-amp compares the two voltages:
- If the temperature voltage (at +) is higher than the reference voltage (at −), the output goes HIGH (near supply voltage)
- If the temperature voltage is lower than the reference, the output goes LOW (near 0V)
-
When the output is HIGH, it turns on the transistor, which energizes the relay. The relay contacts then close and power the load.
Practical Circuit Diagram
A simple temperature-sensitive switch using an op-amp (like LM741) is built as follows:
+Vcc ---[Relay]---[Transistor]--- GND
|
+-- Op-amp output (pin 6)
Op-amp pin 2 (inverting) ---[Potentiometer]--- GND
|
+Vcc
Op-amp pin 3 (non-inverting) ---[Thermistor]--- GND
|
+Vcc
Steps to Build the Circuit
-
Gather components: op-amp (LM741), NTC thermistor (10kΩ at 25°C), potentiometer (10kΩ), transistor (BC547), diode (1N4007), relay (12V coil), resistors, connecting wires, and breadboard or PCB.
-
Set up the temperature sensor: Connect the thermistor in series with a 10kΩ resistor between +Vcc and GND. The junction (temperature voltage) goes to pin 3 of the op-amp.
-
Set the reference voltage: Connect the potentiometer between +Vcc and GND. The wiper connects to pin 2 of the op-amp. Adjust to set your desired switching temperature.
-
Connect the op-amp as comparator: Pin 3 (non-inverting) receives the temperature signal; pin 2 (inverting) receives the reference. Pin 6 outputs the switching signal.
-
Connect the switching stage: Connect pin 6 to the base of the transistor through a resistor (1kΩ). Connect a diode in reverse across the relay coil to protect the transistor.
-
Connect the load: Connect the load (fan, bulb, or buzzer) to the relay contacts with appropriate power supply.
-
Power and test: Apply 12V DC. Adjust the potentiometer to set the temperature threshold. Warm the thermistor (hold it with your hand) and observe the relay click and the load turn on.
Worked Example
A student builds a temperature-controlled fan circuit for a chicken coop in Mwanza. The thermistor reads 10kΩ at 25°C (room temperature) and drops to 3kΩ when the temperature rises to 35°C.
Using a 10kΩ fixed resistor in the voltage divider with +5V supply:
At 25°C: Voltage at op-amp pin 3 = 5V×(10kΩ/(10kΩ+10kΩ))=2.5V
At 35°C: Voltage at op-amp pin 3 = 5V×(3kΩ/(3kΩ+10kΩ))=1.15V
The student adjusts the potentiometer to give 1.5V at pin 2. When the temperature rises above the threshold, the voltage at pin 3 exceeds 1.5V, the op-amp output goes HIGH, the transistor conducts, the relay energizes, and the fan turns on to cool the coop.
Safety Notes
- Always wear gloves and safety boots when working with electronic circuits
- Ensure the workbench is clean and free of metal objects
- Use the multimeter to check for short circuits before powering on
- Keep the power supply turned off while assembling the circuit
Real-life application
In Tanzania, a temperature-sensitive switching circuit is used in small poultry farms around Arusha and Dodoma to automatically turn on fans or alarms when the coop temperature gets too high, protecting chickens from heat stress. A farmer can build this circuit locally using a thermistor, a 12V relay, and a car fan, all available at local electronics shops for around TSh 15,000–25,000, providing an affordable climate control solution.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and electronic components
- Construct circuit using operational amplifier
- Test performance of circuit
- Record test results
- Interpret test results
- Observe safety regulations
Tathmini ya matokeo
Constructed circuit functions as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct electronic circuits using operational amplifiers
Principles: The student should explain the principles of:
- Identifying IC pins
- Connecting ICs
Theories: The student should explain:
- Difference between integrated circuit and discrete component circuit
- Advantages of using integrated circuits (ICs)
- Applications of operational amplifier ICs
- Photo switching circuit
- Temperature sensitive switching circuit
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions in electronics work
- Safe handling of tools, equipment and components.
Swali
What is a temperature-sensitive switching circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado